Macurco TX-12-HS Instructions D'utilisation page 14

Selecting Default Configuration – "dEF"
To select the Default Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. The first selection is the "dEF" or Default setting. Push Enter. If it is already in Default
configuration, there will be no action. If it is not already in Default configuration, "no" will be displayed. Push Next to change it to "yES"
(flashing) then push Enter to confirm the change (solid) and push Enter again to return to "dEF" in the con menu. Push Next until "End"
is displayed then push Enter to get back to normal operation.
Selecting Power Up Test Option – "PUt"
To select the Power Up Test Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then
push the Enter button to enter the Con menu. Then push the Next button to get to the second selection "PUt" or Power Up Test
setting. Push Enter. If the test is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid) and push
Enter again to return to "PUt" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
Selecting Display Option – "dSP"
To select the Display Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. Then push the Next button to get to the third selection "dSP" or Display setting. Push Enter. If
the display is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid) and push Enter again to return to
"dSP" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
Selecting Buzzer Option – "bUZ"
To select the Buzzer Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. The forth selection is the "bUZ" or Buzzer setting. Push Next three times to get to "bUZ" then
Enter. If the display is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid) and push Enter again to
return to "bUZ" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
Selecting Alarm Relay Setting – "ArS"
To select the Alarm Relay Setting, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. The fifth selection is the "ArS" or Alarm Relay Setting. Push Next four times to get to "ArS" then
Enter. If the display is "diS" (disabled) push Next to change it to 5, 10, 15, 20 (default), 25, 30, 35, 40, 45, 50 ppm H2S (flashing) then
push Enter to confirm the change (solid) and push Enter again to return to "ArS" in the Con menu. Push Next until "End" is displayed
then push Enter to get back to normal operation.
Selecting Alarm Relay Configuration – "Arc"
To select the Alarm Relay Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push
the Enter button to enter the Con menu. The sixth selection is the "Arc" or Alarm Relay Configuration. Push Next five times to get to
"Arc" then Enter. If the relay is "nO" (normally open) push Next to turn it to "nC" (flashing) then push Enter to confirm the change (solid)
and push Enter again to return to "Arc" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal
operation.
Selecting Fan Relay Settings – "FrS"
To select the Fan Relay setting, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the Enter
button to enter the Con menu. The seventh selection is the "FrS" or Fan Relay setting. Push Next six times to get to "FrS" then Enter.
If the fan relay is "diS" (disabled) push Next to change it to 2, 3, 4, 5, 6, 7, 8 (default), 9, 10 , 11, 12, 13, 14, 15, 16, 17, 18, 19, 20 ppm
(flashing) then push Enter to confirm the change (solid) and push Enter again to return to "FrS" in the Con menu. Push Next until "End"
is displayed then push Enter to get back to normal operation.
14