Standard Cross Cuts - Ryobi ETMS1825 Manuel D'utilisation

GB
FR DE ES IT NL
OPERATION

Standard cross cuts

Starting position:
- Sawhead fully raised.
- Rotating table in 0° position, the lock screw of the
rotating table is tightened.
- Motorhead is in a vertical (90°) position, bevel
locking lever tightened.
Cutting the work piece:
1. Hold work piece against the fence, use the work
clamp to secure the work piece if possible.
2. Engage trigger(20) and activate/press the safety
lock(6).
3. Slowly swing the sawhead fully down, holding the
handle firmly. When sawing exert only moderate
pressure to keep the motor speed from dropping.
4. Cut the work piece in a single pass.
5. Let the sawhead return slowly to its upper starting
position.
6. If no further cutting is required, turn the saw off by
releasing the trigger(20)
Mitre cuts (Fig.7)
A mitre cut cuts the workpiece at an angle to the fence.
Starting position:
- Sawhead fully raised.
- Motorhead in vertical (90°) position, bevel locking
level, tightened.
Cutting the work piece:
1. Loosen the miter table lock knob(9) of the miter
table(11).
2. Set to desired angle.
3. Tighten the miter table lock knob.
4. Hold work piece against the fence. Use the work
clamp to secure the work piece if possible.
5. Engage trigger(20) and activate/press the safety
lock(6).
6. Slowly swing the sawhead fully down, holding the
handle firmly. When sawing, exert only moderate
pressure to keep the motor speed from dropping.
7. Cut work piece in a single pass.
8. Let the sawhead return slowly to its upper starting
position.
9. If no further cutting is required, turn the saw off by
releasing the trigger(20)
PT DK SE FI NO RU PL
English
NOTE:
The miter table engages at defined angles at the 0 , 15 ,
22.5 , 30 , 45 and 60 position.
Bevel cuts (Fig.10 & 11)
A bevel cut cuts the workpiece at an angle other than 90°.
Starting position:
Cutting the work piece:
1. Loosen the bevel locking level (16) for sawhead tilt at
2. Tilt the motorhead slowly to the desired position.
3. Tighten the bevel locking lever (16).
4. Hold work piece against the fence. Use the work
5. Engage trigger(20) and activate/press the safety
6. Slowly swing the sawhead fully down, holding the
7. Cut work piece in a single pass.
8. Let the sawhead return slowly to its upper starting
9. If no further cutting is required, turn the saw off by
Compound mitre cuts
A compound mitre cut is a combination of the mitre and
bevel cut; this means that in a single pass the work piece
is cut at an angle other than 90° to the fence and material
surface.
Always keep sufficient distance to the saw blade.
Starting position:
Cutting the work piece:
1. Hold work piece against the fence. Use the work
2. Press on the upper half of the ON/OFF switch button
3. Slowly swing the sawhead fully down, holding the
4. Cut work piece in a single pass.
7
CZ HU RO LV LT EE
- Sawhead fully raised.
- Miter table in 0° position, the lock screw of the
rotating table is tightened.
the near of the saw.
clamp to secure the work piece if possible.
lock(6).
handle firmly. When sawing exert only moderate
pressure to keep the motor speed from dropping.
position.
releasing the trigger(20)
DANGER!
When cutting compound mitres the saw blade
is much more exposed than normally-increased
risk of injury.
- Sawhead fully raised.
- Miter table locked in desired position.
- Sawhead tilted to desired angle against the work
piece's surface and locked.
clamp to secure the work piece if possible.
and press the safety lock.
handle firmly. When sawing exert only moderate
pressure to keep the motor speed from dropping.
HR SI SK GR TR