Cleaning And Maintenance; Changing The Bag - Moulinex city space Manuel D'utilisation

903397-01_MO24_city-space_903397/01 10/07/13 09:32 Page9
• If your vacuum cleaner is equipped with a telescopic tube* (20) : push the clamping button forward, extend
the tube to the desired length and release the button to lock the tube in place -
the two tubes* (21) by turning slightly -
• Fit the tube extension* (22) if necessary.
• Fit the required accessory onto the end of the tube:
- For rugs and carpets: use the "all floors" nozzle (23) with the brush tucked in -
(27 or 28*).
- For wood and hard floors: use the "all floors" nozzle (23) with the brush pulled out (
use the parquet nozzle* directly (24).
- For corners and hard to reach spots: use the crevice tool convertible into brush (26) in the flat position.
- For upholstery and delicate surfaces: use the crevice tool convertible into brush (26) or the upholstery nozzle*
(25).
Attention! Always switch off and disconnect your vacuum cleaner before changing any accessories.
Plugging and switching on the appliance
• Unwind the power cord completely, plug in your vacuum cleaner (
8.
• Set the suction power using the manual power switch on the handle: open the regulation vent in order to
manually decrease the suction power, for example: on fragile surfaces –
Storage and transport of the appliance
• After each use, switch your vacuum cleaner off by pressing on the ON/OFF pedal (2) –
fig. 10
. Store the cord by pressing on the wind pedal (3) -
• In the vertical position, place the nozzle (23) in its storage compartment on the appliance (1b) –
• In the horizontal position, place the nozzle (23) in its storage compartment on the appliance (1a) –
• You may easily transport your vacuum cleaner by the transport handle (6).

5. CLEANING AND MAINTENANCE

Important: Always switch off and unplug your vacuum cleaner before maintenance or cleaning.

Changing the bag

• The Bag full indicator (4) indicates that the bag is full or saturated. If you notice a reduction of the efficiency
of your appliance, set the power at maximum and hold the nozzle above the ground. If the Bag full indicator
remains red, replace the bag.
• Remove the flexible hose (19) from the suction opening (9) - fig. 2.
• Open the lid (8) of your vacuum cleaner -
a) If your vacuum cleaner is equipped with a paper bag* :
• Remove the bag support (15) from the bag compartment (7) –
its base (15) by sliding it through the runners -
• Throw the bag in the rubbish bin -
• Place a new bag in the bag support (15) –
it on the runners (16) –
• Make sure the bag and the bag support are correctly positioned before closing the lid (8).
b) If your vacuum cleaner is equipped with a textile bag* :
• Remove the bag support (15) from the bag compartment (7) –
from its support (15) by sliding it through the runners -
• Open the textile bag using the zipper -fig. 16c- then empty it above a rubbish bin –
• Clean the bag with running water –
• Leave the bag to dry for at least 24 hours (do not replace the bag until it is perfectly dry) –
• Close the textile bag : make sure that the zipper is completely closed -
the appliance.
• Place a new textile bag in the bag support, then place the base inside the compartment by sliding it on the
fig. 16h
runners (16) –
• Make sure the textile bag and the bag support (15) are correctly positioned before closing the lid (8).
*Depending on model: it means special equipment for some models or optional accessories.
fig. 4.
fig.14.
fig. 15b
fig.15c
.
fig. 15d
fig. 15e
.
fig. 16e
.
.
fig. 7 ) and press the ON/OFF pedal (2) -
fig. 9
.
fig.11
.
fig.15a , then remove the paper bag (18a) from
.
, then place the base inside the compartment by sliding
fig.16a , then remove the textile bag (18b)
fig. 16b .
fig. 16g
- before placing it back inside
fig. 3.
Otherwise, assemble
fig. 5
, or the turbo-brush*
fig. 6) or, for best results,
fig.
fig. 8
- and unplug it –
fig. 12 .
fig. 13 .
fig. 16d .
fig. 16f
.
9
EN