Quick A-F 300W Manuel De L'utilisateur page 15

POS. DESCRIPTION
5 Pin
6 Gasket/oval-shaped jig
7A Studs aluminium base
7B Studs fiber-glass base
8 Washer
9 Spring washer
10 Nut
11 Gearbox
12 Screw
13 Washer
14A Electric motor 300W 12V
14B Electric motor 400W 12V
14C Electric motor 400W 24V
15 Gasket/round jig
16 Round base
17 Sensor
18 Screw
19 Rope/chain stripper Round base
20 Key
21 Short shaft
22 Long shaft
23 Screw
24 Screw
25 External circlip
26 Bearing
27 Internal circlip
28 Oil seal
29 Ring
30 Clutch cone
31 Magnet
32 Gypsy
33 Gypsy cover
34 Drum
35 Bush
36 Handle
37 Paper gasket
38 Screw
39 Screw for pressure lever
40A Black pressure lever
40B White pressure lever
41 Spring for pressure lever
CODE
M S R 0 4 X 0 0 0 0 0 0
P G B S V 0 4 0 0 0 0 0
M B P 0 8 0 6 0 7 X 0 0
QUICK windlasses are manufactured with materials
M B P 0 8 0 6 0 8 X 0 0
resistant to marine environments. In any case, any salt
M B R 0 8 X 0 0 0 0 0 0
deposits on the outside must be removed periodically to
M B R 0 8 X D E 0 0 0 0
avoid corrosion and damage to the equipment. The parts
M B D 0 8 M X E N 0 0 0
M R 0 4 0 0 0 0 0 0 0 0 where salt may have built up should be washed
M B V 0 5 1 6 M X E 0 0
thoroughly with fresh water.
M B R 0 5 X 0 0 0 0 0 0
Once a year, the drum and the gypsy are to be taken
E M F 0 3 1 2 0 0 0 0 0
apart as follows:
E M F 0 4 1 2 0 0 0 0 0
E M F 0 4 2 4 0 0 0 0 0
Drum version
P G B S C 0 4 0 0 0 0 0
Use the handle (36) to loosen the bush (35); pull off the
S G M S C 0 4 C 0 0 0 0
drum (34) and the top clutch cone (30); loosen the fixing
K N R E E D C L 0 0 0 0
screws (2 or 18) of the rope/chain stripper (3 or 19) and
M B V 0 6 2 0 M X S C 0
remove it. Pull off the gypsy (32).
S G M S N 0 4 C 0 0 0 0
M B H 0 6 0 6 5 0 F 0 0
No-drum version
M S A S 0 4 2 0 3 R 1 0
Use the handle (36) to remove the gypsy cover (33);
M S A S 0 4 2 4 5 R 1 0
remove the top clutch cone (30); loosen the fixing screws
M B H 0 6 0 6 2 5 F 0 0
(2 or 18) of the rope/chain stripper (3 or 19) and remove
M B H 0 6 0 6 6 0 F 0 0
it and pull off the gypsy (32).
M B A E 1 7 1 5 Y 0 0 0
M B J 6 0 0 3 2 R S 1 0
Clean all the parts removed to avoid corrosion, and grease
M B A N 3 5 1 5 Y 0 0 0
the shaft thread (21 and 22) and the gypsy (32) where
P G P R L 1 7 3 5 7 0 0
the clutch cones rest (use grease suitable for marine
M B A C 1 7 2 0 Y 0 0 0
environment) (30).
M S F 0 4 R 1 0 0 0 0 0
Periodically grease the hinge pin (5) of the inspection door
K P M C 0 8 0 6 0 0 0 0
(only windlasses with aluminium bases).
M S B 0 4 0 6 0 0 0 0 0
S G M S G B 0 4 0 0 0 0
Remove any oxide deposits from the terminals of the
S G M S E 0 4 R 1 0 0 0
electric motor and the reversing solenoid unit; grease
S G M S D 0 4 0 0 0 0 0
them.
M S H D 0 0 0 0 0 0 0 0
P G B M R 0 4 0 0 0 0 0
M B H 0 4 0 4 1 5 F 0 0
M S M V T 0 4 0 0 0 0 0
P D L V T D 0 4 0 0 0 0
P D L V T D 0 4 W 0 0 0
M M T N D 0 4 0 0 0 0 0
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on
the windlass. Carefully remove the chain or rope
from the gypsy or the rope from the drum.
WARNING: the electric motor of the windlass is not
water-proof; it is water resistant and must not be
immersed.
15