Virutex FR156N Mode D'emploi page 7

Weight........................................................1,6 Kg
Weighted equivalent continuous
acoustic pressure level A..................................................88 dBA
Acoustic power level A.......................................................99 dBA
Uncertainty...................................................................K = 3 dbA
Wear ear protection!
Vibration total values.................................................a
Uncertainty....................................................................K: 1.5 m/s
3. STANDARD EQUIPMENT
Inside the box you will find the following items:
Model FR156N
Trimmer FR156N fitted with:
• Round trimming head (V3) 5646365. Attached.
• Corner rounding bit 3 with bearing HM 1140106.
• A/f key: 11 mm for the motor shaft.
• A/f key: 19 mm for the chuck collet.
• Head bases with a pitch diameter of 26 and 30.
Model FR256N Set
Trimmer FR156N fitted with:
• Trimming head CA56U 5600060. Attached.
• Corner trimming accessory 5646343.
• Round trimming head (V3) 5646365.
• Corner rounding bit 2 with bearing HM 1140123.
• A/f key: 11 mm for the motor shaft.
• A/f key: 19 mm for the chuck collet.
• Head bases with a pitch diameter of 26 and 30.
4. GENERAL DESCRIPTION
OF THE FR156N TRIMMER
The main function of the machine is the finishing of PVC,
melamine and wooden edges. These may be straight and
angled or curved, depending on the bit used. Shaped
finishes can also be obtained using different VIRUTEX bits
with bearings. The machine is fitted with a dust collector
connection for attaching our AS182K and AS282K dust
collectors or any other industrial dust collector, using
the standard dust collector attachment (Ref. 6446073).
The dust collector connection incorporates a sprung
brake pivot R (Fig. 8), whose purpose is to slow down
the outer bearing ring, preventing it turning with the
bit and possibly damaging the surface of the panel when
placing the trimmer in the working position.
5. ADJUSTMENTS
Unplug the machine from the electrical
outlet before making any adjustments.
To adjust the bit outlet, loosen knob B on the head and
turn the machine as appropriate up or down until the
desired bit outlet is achieved. Fasten knob B in place
again (Fig. 3).
6. STARTING UP THE MACHINE
To start the machine, press button E forward (Fig. 1) to
the on position. To stop the machine, simply press the
: 2.6 m/s
2
back of the switch and it will return to the off position.
h
2
The electronic control enables you to work at the ideal
speed for each type of job and bit. Adjust the speed
using button K (Fig. 2).
7. CHANGING THE BIT
Loosen knob B (Fig. 3) and remove the head. To change
the bit (Fig. 4), block the motor shaft using key C, unscrew
the chuck with key D and remove the bit.
Insert the new bit into the housing and hold it in place
using the service keys, then fit the head back in position.
8. CHANGE OF THE TRIMMING HEAD BASE
The machine is delivered from factory with the
trimming head base d.20 for bits of 3 mm radius. When
working with a bit 6 mm radius it will be necessary
to change this base for the one d.26. If a bit 8 mm
radius is used the standard base must be replaced for
the one d.30. Both extra bases are included as standard
equipment with the machine.
To change base M, first remove the dust collector
connection L, by unscrewing knob N (Fig. 7). Once
connection L has been removed, unfasten screws P to
remove base M and fit the appropriate base for the
bit you are going to use. Next, fit the dust collector
connection L by screwing in knob N.
9. TRIMMING CORNERS
Disconnect the machine from the power
supply before this operation.
Make sure that the collet diameter mat-
ches the shank of the bit to be used.
Never use the machine without fitting
the head first.
Disconnect the machine from the
power supply before this operation.
7