HUROM H-200 Série Mode D'emploi page 7

9. How to Disassemble and Clean
12
※ After the product stop operating completely,
unplug the power cord with your dry hands.
The motor is still slowing down after the
appliance is turned off, so wait about 3 seconds
before separating the chamber.
01 Separate the chamber set from the base. Turn
the hopper open and pull off the parts in order.
02 Wash the parts under running water with the
cleaning brush.
03 Wash the chamber with the pulp outlet cover
and the juice cap wide open.
04 Wipe the base with a dry towel or soft cloth.
05 For silicon rings, detach and wash them after
use. -There may be juice residues stuck in.
(Hopper ring, juice cap, extraction cap, sealing,
and chamber ring)
06 You can sterilize the parts by soaking them in
warm water with baking soda, citric acid, or
vinegar.
※ Failure to clean the product right after use can cause
its stainless steel components and other parts to corrode
or discolor due to salt and pulp of the ingredients. In
addition, contaminants may dry up and get stuck inside
the product, making disassembly or cleaning difficult
or adversely affecting the product's performance. Be
sure to clean and air dry the appliance completely after
use and store it at a clean place. For long-term storage,
clean the appliance with the cleaning brush in advance.
Do not clean the product with boiling water or subject it to
high temperature. Do not use abrasive cleaning tool like
kitchen sink cleaner, or stainless-steel sponge. Do not
use a dishwasher or dish dryer for the product.
10. Before
Check the following before asking for repair. For follow-up service and any inquiry
you may have while using the product, please contact our Customer Center, or
Requesting Repair
homepage at http://www.globalhurom.com Check the manufacturer's number or
the number under the barcode when requesting for follow-up service or parts.
01. When the product starts This is the sound of when the motor and the squeezing screw are connected.
operation, it will make a "clicking" and not a sign of malfunction.
sound.
02. The product won't operate with Make sure the chamber set and main body are assembled properly.
the main body only. Ensure the product is unplugged before assembling or disassembling it.
03. Align the safety sensors. Make sure they are assembled in accordance with the assembly guide.
Ensure the product is unplugged before assembling or disassembling it.
04. The product does not work. Check if the power cord is plugged properly.
The machine may not work after prolonged use (30 minutes or longer).
It will resume normal operation once the main body (motor) cools down.
Check if the hopper fits properly.
If the hopper is connected incorrectly, the product will not operate properly.
It will operate only when the lock symbol on the chamber is perfectly aligned
with the assembly guide on the hopper (②-3). Ensure the product is assembled
in accordance with the assembly guide. Refer to the assembly page 8 of the
instruction manual.
05. The product suddenly stops Is the hopper overloaded with juicing ingredients, or are the ingredients too big?
running. Refer to the manual page 11, and activate reverse rotation.
06. There are cracks on the screw In addition to the straight molding marks on the top and sides of the screw, there
and scratch marks on the upper are curved marks that were created while it was being molded.
part of the screw. These marks are normal and they have no impact on your use of the screw.
07. Juice leaks through the pulp A little juice may come out of the pulp outlet depending on the ingredient.
outlet immediately upon inserting This is not a product defect but the result of the characteristics of the ingredient.
ingredients. The leakage will stop once the product starts running. If the leakage persists,
contact our Customer Service Center.
08. Juice flows back into the Did you operate the product with the juice cap closed? Closure of the juice cap
hopper. may cause a back flow up to the hopper. If the flow gets clogged even after opening
the juice cap, open the hopper lid and empty out the inside.
09. Juice leaks between the hopper Is the hopper silicone ring assembled correctly?
and the chamber, or between the Juice will leak if the chamber silicone ring has been assembled upside down or
chamber and the main body. incompletely. Check if the silicon rings have been assembled correctly.
10. I can't open the hopper. There may be excessive pulp remaining inside. If the remaining pulp is discharged
by turning on the machine, or the machine is rotated in reverse for 10 seconds two
or three times, the hopper will open smoothly.
Perhaps you put foreign or solid substances (hard seeds such as persimmon
seeds)? If you have put foreign or solid substances, attempting to run the product
in reverse direction may further damage the component. Thus, contact our
Customer Service Center and request after-sales support.
11. The chamber is vibrating The product may wobble slightly due to the vibrations produced by the main
(during juicing). body's motor. It may vibrate depending on the ingredient's hardness or toughness.
This is not a malfunction but a normal sign as it is caused by the rotating screw.
The product may seem to vibrate more when juicing solid ingredients (e.g.,
carrots, potatoes, radishes, beets, or kohlrabies) than when juicing soft and
watery ingredients. (e.g., carrot. potato, radish, beet, kohlrabi, etc)
12. Pulp outlet is covered, but the Even if the lever is closed, pulp may still come out naturally.
pulp comes out. The velocity and amount of pulp discharge may differ according to the ingredients
used.
13