Kyocera JS-710 Guide D'installation
  1. Manuels
  2. Marques
  3. Kyocera Manuels
  4. Accessoires d'imprimante
  5. JS-710
  6. Guide d'installation
Kyocera JS-710 Guide D'installation

Kyocera JS-710 Guide D'installation

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
INSTALLATION GUIDE FOR THE JOB SEPARATOR
GUIDE D'INSTALLATION DU SEPARATEUR DE TRAVAUX
GUÍA DE INSTALACIÓN PARA SEPARADOR DE TRABAJOS
INSTALLATIONSANLEITUNG FÜR JOBTRENNER
GUIDA ALL'INSTALLAZIONE DEL SEPARATORE
ジョブセパレータ設置手順書
JS-710

Publicité

Table des Matières
loading

Manuels Connexes pour Kyocera JS-710

Sommaire des Matières pour Kyocera JS-710

  • Page 1 INSTALLATION GUIDE FOR THE JOB SEPARATOR GUIDE D’INSTALLATION DU SEPARATEUR DE TRAVAUX GUÍA DE INSTALACIÓN PARA SEPARADOR DE TRABAJOS INSTALLATIONSANLEITUNG FÜR JOBTRENNER GUIDA ALL’INSTALLAZIONE DEL SEPARATORE ジョブセパレータ設置手順書 JS-710...

  • Page 3: Pièces Fournies

    E Copy tray ..........1 I Stationary plate F ........1 J Stationary plate R ........1 F M4 × 10-tap-tight S screws ...... 6 K M4 × 10 tap-tight screws......9 G Wire saddle..........1 Supplied Parts L Shoulder screw ........1 H Cover left OP ...........

  • Page 4: Installation Procedure

    Installation procedure Remove the left front cover. 4. Remove clip support (3). 5. Remove two screws (4) and then remove left When installing a job separator, be sure to turn 1. Open the front cover. front cover (5). the MFP power off and disconnect the power 2.
  • Page 5 9 9 9 8 8 8 10 11 13 C Remove the copy cover. Attach the retainer. 6. Unlock copy cover pawl (6) and then remove 8. Remove the fixing tape of retainer (C) and pull out the connector (10). ejection cover (7).
  • Page 6 Attach the copy tray. Attach the job separator. 11. Insert copy tray (E) into the right-side groove of the MFP. Push copy tray (E) until its hook (12) is 13. Open left cover (16). engaged with the MFP projection (13). 14.

  • Page 7: Fixer Le Couvercle Supérieur Gauche

    15. Insert job separator (A) in the direction of the 16. Attach wire saddle (G) to the left side of the Attaching the upper left cover JS. arrow and secure it with two M4 × 10-tap- MFP. 19. Remove the screw (21) from the rear side of tight S (F) screws.
  • Page 8 20. Use the screw (21) that has been removed 21. Engage the pawl of attached engaging fitting (22) with the MFP and secure upper left cover JS by Procedure 19 to attach engaging fitting (D) with two M4 × 10-tap-tight S (F) screws. (22) to the rear side of the supplied upper left cover JS (D).
  • Page 9 When installing the document finisher to the MFP, no need to per- Assemble the left front cover JS. form step 22. 23.Remove the screw (23) from the left cover that has been removed in 22. Attach cover left OP (H) to upper left cover JS (D) by engaging the pawl Procedure 5.
  • Page 10 25. Fit the pawl of left front cover 1 (24) into the hole of left front cover JS (B) and assemble them. Attach the left front cover JS. 26. Fit the part (27) into the groove (26) of left front cover JS (B). 28.
  • Page 11 29. Attach clip support (3) that has been [Operation check] removed in Procedure 4. 1. Insert the power plug of the MFP into an out- 30. Set the toner container [black] and turn toner let and then turn the main power switch on. container lock lever (1) counterclockwise.
  • Page 12 2006. 1 303KN56710 Rev.1.0...

Table des Matières