Table des Matières
Publicité
Liens rapides
V53i
only
ANS Z21.10.3
●
CSA 4.3
V53e
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING
result causing property damage, personal injury or death.
- Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone in
•
your building.
Immediately call your gas supplier from a neighbor's phone.
•
Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fire
•
department.
- Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
Tankless Water Heater
Operation and Installation Manual
V53i ..................... REU-VB2020FFU-US
V53e .................... REU-VAM1620W-US
Certified for installation in manufactured (mobile) homes.
Table of Contents ..................... 2
Operating Instructions .............. 5
Maintenance .......................... 12
Error Codes ............................ 13
Installation Instructions .......... 17
Consumer Support ................. 44
French Version ....................... 47
Register your product at www.rinnairegistration.com or
call 1-866-RINNAI1 (746-6241)
If the information in these instructions is not
followed exactly, a fire or explosion may
Publicité
Chapitres
Table des Matières
Manuels Connexes pour Rinnai V53i
Sommaire des Matières pour Rinnai V53i
-
Page 1: Table Des Matières
Tankless Water Heater Operation and Installation Manual V53i ..... REU-VB2020FFU-US V53e ....REU-VAM1620W-US Certified for installation in manufactured (mobile) homes. Table of Contents ..... 2 Consumer Safety Information .. 4 Operating Instructions ....5 Maintenance ......12 Error Codes ......13... - Page 2 Maximum Vent Length ......28 Setting the Water Volume ......10 Vent Products .......... 28 Filling the Tub ..........11 Flue Installation - Concentric Venting (V53i) . 29 Setting Controller to Mute ......11 Flue Terminal Clearances Setting the Clock ..........11 (ANS Z21.10.3, CSA 4.3...
-
Page 3: V53I
(mobile) homes * Minimum flow may vary slightly depending on the temperature setting and the inlet water temperature. Rinnai is continually updating and improving products. Therefore, specifications are subject to change without prior notice. The maximum inlet gas pressure must not exceed the value specified by the manufacturer. The minimum value listed is for the purpose of input adjustment. -
Page 4: Consumer Safety Information
• Power Failure: The appliance will cut off the gas if it loses electrical power. Description of Operation The Rinnai water heater is one of the most advanced Installation of the temperature controller is highly water heaters available. It provides a continuous recommended. -
Page 5: Operating Instructions
Operating Instructions The V53i and V53e models do not come with a temperature controller. There are several models of temperature controllers that can be purchased separately. Their description, operation, and installation are provided in this manual in case a temperature controller is purchased and installed. -
Page 6: Temperature Controllers - Models
Button * Requires the transceiver, MC- 502RC-1US-M, to be connected to the water heater. Refer to the MC-502RC-1US-S manual and the Wireless Controller Installation Instructions for complete details on features, operation, and installation. V53i & V53e Operation and Installation Manual... - Page 7 Water Volume Temperature Sound Volume Selection MC-100V-1US Dimensions (inches): 5.0 W x 4.75 H x 0.75 D Temperature In Use Selection Indicator Function Temperature Display Priority Button and Indicator Clock ON/OFF Button Call V53i & V53e Operation and Installation Manual...
-
Page 8: How To Set The Temperature
▲ or ▼ button cycles through through the volume levels in the the volume levels in the order order below. below. Medium Volume Off Volume Off Sound High Volume Low Volume (default) (beep) (no beep) V53i & V53e Operation and Installation Manual... -
Page 9: Temperature Controller Settings
Water temperatures over 125º F (52º C) can cause severe burns or scalding. Refer to the Danger Alert on water temperatures. Rinnai shall not, in any event, be liable for damages resulting from such misuse or misapplication. -
Page 10: Using The Water Smart / Bath Fill Function
3. Press the “Temp” ▲ or ▼ buttons • Monitor and remain by the bath to obtain the desired temperature Over Filling while the water is running. setting. • Use a low bath fill volume less than 25 gallons. V53i & V53e Operation and Installation Manual... -
Page 11: Filling The Tub
Press the “Function” button twice within 10 seconds to set the clock. Press the ▲ or ▼ button to reach the desired time. The clock on the BC-100V automatically shows the time which has been set on the MC-100V. V53i & V53e Operation and Installation Manual... -
Page 12: Maintenance
If you receive Error Code “LC”, refer to the procedure, Flushing the Heat Exchanger. Refer to the section on Water Quality to see if your water needs to be treated or conditioned. (When checking maintenance code history, “00” is substituted for “LC”.) V53i & V53e Operation and Installation Manual... -
Page 13: Error Codes
Error Codes The Rinnai water heater has the ability to check its own operation continuously. If a fault occurs, an error code will flash on the display in the front panel and on the temperature controller if installed. This assists with diagnosing the fault and may enable you to overcome a problem without a service call. - Page 14 Ensure you have at least the minimum flow rate required to fire unit. Ensure turbine spins freely. Measure the resistance of the water flow control sensor. Check for DC shorts at components. V53i & V53e Operation and Installation Manual...
-
Page 15: Trouble Shooting For Common Issues
Make sure there is gas, water, and electricity to the During colder weather when the exhaust temperature Rinnai water heater (power is turned on and the gas is is much hotter than the outside air, the exhaust fumes turned on). -
Page 16: Flushing The Heat Exchanger (Error Code: Lc Or 00)
13. Restore electrical power to the water heater. CLEAN THERMISTORS Remove and clean thermistors with a soft cloth or sponge after removing O-rings. Cleaning solution is 4 gallons of undiluted virgin, food grade, Circulating Pump white vinegar. V53i & V53e Operation and Installation Manual... -
Page 17: Installation Instructions
Rinnai highly recommends all installers attend a product knowledge class. The V53i and V53e are certified for installation in manufactured (mobile) homes. For information on a Rinnai Training Course or for questions on installation call 1-800-621-9419. -
Page 18: Clearances From Appliance
Refer to the brackets weight of the water heater in the Specifications section. NOTE: Rinnai water heaters should be installed in an upright position. Do not install upside down or on it side. V53i & V53e Operation and Installation Manual... -
Page 19: Electrical Connection
Rinnai water heater. If the Rinnai water heater is not of the gas type that the • The gas supply line shall be gas tight, sized, and so building is supplied with, DO NOT connect the water installed as to provide a supply of gas sufficient to heater. -
Page 20: Pipe Sizing Procedure - Example
BTU/hour. Example: The heating value of natural gas for your location is 1000 BTU/FT . The gas input of the V53i is 150,000 BTU/HR. Additional appliances at the location require 114,000 BTU/hr. Therefore the cubic feet per hour = (150,000 + 114,000) / 1000 = 264 FT /HR. -
Page 21: Water Piping General Instructions
• Ensure that the water filter on the Rinnai water • Purge the water line to remove all debris and air. heater is clean and installed. -
Page 22: Freeze Protection Methods
1.Do not operate the water heater if it or the external piping is frozen. 2.Close the gas and water valves and turn off the power. 3.Wait until the water thaws. Check by opening the water supply valve. 4.Check the water heater and the piping for leaks. V53i & V53e Operation and Installation Manual... -
Page 23: Freeze Protection Piping
Rinnai water to prevent freezing damage. Water Heater The unit may be drained manually. However, Rinnai highly recommends that drain down solenoid valves be installed that will automatically drain the unit if power is lost. Rinnai also recommends the installation... -
Page 24: Error Indication Or Air Handler Control Switch
Error Indication or Air Handler Control Switch (V53i) When using the Rinnai water heater with an Error Indication Switch, switch No. 4 in the bank of 8 switches should be in the off position. This is the default position. To connect the water heater to the Rinnai Air Handler, the Control Switch is necessary to function as the electrical connection. -
Page 25: Recommended Piping For Circulation Systems
IMPORTANT: Connect the building Electric Water return line to the hot water supply line Heater as close as possible to the Rinnai Water Building Heater. Fixtures This is not an engineered drawing. It is intended only as a guide and not as a replacement for professionally engineered project drawings. -
Page 26: Optional Piping For Circulation Systems
It is the Check Valve responsibility of the contractor/engineer to ensure installation is in Boiler Drain Valve accordance with all local building codes. Confer with local building Pressure Relief Valve Solenoid Valve officials before installation. V53i & V53e Operation and Installation Manual... -
Page 27: Venting Instructions (V53I) Intake / Exhaust Guidelines
• Vent diameter must not be reduced. If it becomes necessary to access an enclosed vent system for service or repairs, Rinnai is not responsible • Do not connect the venting system with an existing for any costs or difficulties in accessing the vent vent or chimney. -
Page 28: Maximum Vent Length
If you have a longer vent length, switch no. 1 is required to be in the OFF position. This ensures the water heater will run properly. Blocked flue error codes and shutdowns may result if switch no. 1 is not in the correct position. Vent Products Listed and Tested Vent Products for V53i ......REU-VB2020FFU-US Manufacturer Product Parts... -
Page 29: Flue Installation - Concentric Venting (V53I)
5. Install the 4 screws at the vent top and tighten the 4 screws at the bracket. Secure the first vent component to the water heater Securing Screw with one self-tapping screw at the hole located above the condensate collector. V53i & V53e Operation and Installation Manual... -
Page 30: Flue Terminal Clearances
For clearances not specified in ANSI Z223.1/NFPA 54 or CSA B149.1, clearances are in accordance with local installation codes and the requirements of the gas supplier. Clearance to opposite wall is 24 inches (60 cm) for Canada and US. V53i & V53e Operation and Installation Manual... -
Page 31: Additional Clearances (V53I)
(0.61 m) to wall or parapet 24" (0.30 m) between Rinnai terminals at same level INSIDE CORNER (1.52 m) between 60" Rinnai terminals at different levels 12" (0.30 m) between Rinnai terminals at same level V53i & V53e Operation and Installation Manual... -
Page 32: Additional Clearances (V53E)
Additional Clearances (V53e) Local codes supersede these clearances. • Avoid termination locations near a dryer vent. • Avoid termination locations near commercial cooking exhaust. V53i & V53e Operation and Installation Manual... -
Page 33: Connecting Multiple Water Heaters
Connecting Multiple Water Heaters The V53i can use the EZConnect™ cable which is Number of an optional accessory that connects 2 water Connected Accessories Necessary: heaters and allows them to function as one hot Water Heaters: water source. (1) EZConnect™ Cable... - Page 34 CAN/CGA-B149.1 ou CAN/CGA-B149.2 Codes d'Installa- tion. V53i & V53e Operation and Installation Manual...
-
Page 35: Temperature Controller Installation Location
328 ft (100 m) controller to the water heater depends on the total number of wired controllers connected to the water 164 ft (50 m) heater. 3 or 4 65 ft (20 m) V53i & V53e Operation and Installation Manual... -
Page 36: Mounting The Controller (V53I)
2. 7. Disconnect the power from the Rinnai water securing screw heater. 1-21/32" 8. Remove the cover of the Rinnai water heater. wiring hole 9. Remove the plastic cover from the PCB and 3-5/16" electrical connections. -
Page 37: Mounting The Controller (V53E)
1. Determine a suitable location for the controller. 2. Make three holes in the wall as shown. 3. Run the cable between the controller and the Rinnai water heater or the controller and another controller. 4. Remove the face plate from the temperature controller using a screwdriver. -
Page 38: Operating Instructions
1. Turn off all electric power to the appliance using 3. Locate the manual gas valve on the side of the the ON/OFF button. heater. Turn the manual valve clockwise to the full OFF position. 2. Set the thermostat to lowest setting. V53i & V53e Operation and Installation Manual... -
Page 39: Technical Data
Technical Data Pressure Drop Curve V53e V53i Water Flow (gpm) Outlet Flow Data V53i V53e delta T - Temperature Rise (ºF) V53i & V53e Operation and Installation Manual... -
Page 40: Space Heating
Iron Components Do not use Rinnai water heaters directly for space heating applications involving iron radiators or applications with any iron components. Iron components may oxidize creating rust that will clog the inlet filter of the Rinnai water heater. V53i & V53e Operation and Installation Manual... -
Page 41: Dimensions
2.0 (50) From base to hot connection 1.7 (42) 1.6 (42) * This is the minimum dimension from the wall. The wall bracket is adjustable to allow an additional 1.57 inches (40 mm). V53i & V53e Operation and Installation Manual... -
Page 42: Ladder Diagrams
Ladder Diagram (for V53i) V53i & V53e Operation and Installation Manual... - Page 43 Ladder Diagram (for V53e) V53i & V53e Operation and Installation Manual...
-
Page 44: Consumer Support
Limited Warranty What is covered? This Warranty covers any defects in materials or workmanship when the product is installed and operated according to Rinnai written installation instructions, subject to the terms within this Limited Warranty document. This Warranty applies only to products that are installed correctly. - Page 45 Replacement of the product may be authorized by Rinnai only. Rinnai does not authorize any person or company to assume for it any obligation or liability in connection with the replacement of the product. If Rinnai determines that repair of a product is not possible, Rinnai will replace the product with a comparable product at Rinnai’s discretion.
-
Page 46: State Regulations
State Regulations NOTICE BEFORE INSTALLATION Rinnai direct-vent appliance must be installed by a state qualified or licensed contractor and a properly trained Rinnai Installer. If you are not properly trained, you must not install this unit. IMPORTANT: In the State of Massachusetts (248 CMR 4.00 & 5.00) -
Page 47: Que Faire Si Vous Sentez Une Odeur De Gaz
Espacements pour terminaison de cheminée l'appareil installé. (ANSI Z21.10.3, CSA 4.3) ........ 58 CONSOMMATEUR : Conservez ce manuel Installation de conduit de cheminée (V53i) ..59 comme référence ultérieure. Instructions d'utilisation ........60 Diagramme en escalier ........61 Support à la clientele / Pour une traduction complète du manuel en français,... -
Page 48: Instructions D'utilisation
à distance et la température réelle au robinet, du fait des conditions d'environnement, ou de la longueur de tuyauterie depuis le chauffe-eau. Manuel d'installation et d’utilisation – V53i & V53e... -
Page 49: Plages De Température Avec Un Contrôleur De Température
à une température sûre. Arroser des températures plus de 125º F (52º C) peut causer des brûlures ou scalding sévère. Se référer à l'Alerte de Danger sur les températures d'eau. Rinnai ne fait pas, en tout cas, être responsable des dommages qui résultent de tel usage impropre ou tel mauvais usage. -
Page 50: Entretien
(Lors de la vérification de l'historique des anomalies pour l'entretien, le code « 00 » aura remplacé « LC ».) Manuel d'installation et d’utilisation – V53i & V53e... -
Page 51: Instructions D'installation
être obstrué. • • La V53i ne doit pas être installé à l'extérieur. Cet appareil ne convient pas pour une utilisation dans une application comme le chauffage d'eau de piscine ou de •... -
Page 52: Écartements Par Rapport À L'appareil
Remarque : Les chauffe-eau de Rinnai doit être installé dans une position verticale. N'installez pas à l'envers ou sur ce côté. Manuel d'installation et d’utilisation – V53i & V53e... -
Page 53: Installation À Altitude Élevée
être rincée avec de l'eau -eau Rinnai. Un raccord union peut être utilisé sur la après le test, sauf si vous avez pu déterminer que la connexion au-dessus de la vanne de coupure pour solution de détection utilisée n'était pas corrosive). -
Page 54: Tuyauterie D'eau
à eau potable. potable. • • Purgez la conduite d'eau pour en éliminer les débris et Le filtre d’eau du chauffage Rinnai dout être propre et l'air. Des débris entrant dans le chauffe-eau Rinnai installé. pourraient l'endommager. Soupape de sûreté... -
Page 55: Tuyauterie Recommandée Pour Installation De Base
Confer Soupape de décharge Pressure Relief Valve Solenoid Valve Électrovanne with local building officials before installation. Manuel d'installation et d’utilisation – V53i & V53e... -
Page 56: Instructions De Ventilation (V53I) Consignes Pour Aspiration/Évacuation
AVIS l'appareil. Des dispositions doivent être prises pour éviter que du • Le chauffage de l'eau V53i a un collecteur de condensat condensat n'entre dans le chauffe-eau. Sans un drainage intégré. adéquat et un rejet, le condensat peut endommager •... -
Page 57: Longueur Maximum De Ventilation
Téléphone : 800-772-0739 Téléphone : 800-835-2830 Fax : 678-829-1666 Fax : 413-863-4803 316-943-2351 Site Web : www.rinnai.us Courriel : custsvc@heat-fab.com Fax : 316-943-2717 Site Web : www.heatfab.com Courriel : info@mtlfab.com Site Web : www.metal-fabinc.com Manuel d'installation et d’utilisation – V53i & V53e... -
Page 58: Espacements Pour Terminaison De Cheminée
Pour les espacements non spécifiés dans ANSI Z223.1/NFPA 54 ou CSA B149.1, il faut appliquer les valeurs conformes aux normes locales d'installation et aux exigences du fournisseur de gaz.. L'espacement par rapport au mur opposé est de 24" (60 cm) pour Canada et USA. Manuel d'installation et d’utilisation – V53i & V53e... -
Page 59: Installation De Conduit De Cheminée (V53I)
5. Remettez les 4 vis du haut de ventilation et resserrez les 4 vis du support. Fixez la pièce de ventilation connectée sur le chauffe-eau Vis de fixation avec une vis autotaraudeuse dans le trou situé au dessus du collecteur de condensat. Manuel d'installation et d’utilisation – V53i & V53e... -
Page 60: Instructions D'utilisation
Repérez la vanne de gaz manuelle sur le côté du son bouton M/A. chauffe-eau. Fermez-la en la tournant à fond dans le sens horaire (position OFF). Réglez le thermostat sur la consigne la plus basse. Manuel d'installation et d’utilisation – V53i & V53e... -
Page 61: Diagramme En Escalier
THERMISTANCE DE SORTIE D'EAU THERMISTANCE DE SORTIE D'EAU 2 THERMISTANCE D'É- CIRCUIT DE CIRCUIT DE CHAGEUR THERMIQUE THERMIS- THERMIS- TANCE TANCE THERMISTANCE D'É- THERMISTANCE DE CHAGEUR THERMIQUE BRÛLEUR THERMISTANCE DE TEMPÉRATURE D'AIR Manuel d'installation et d’utilisation – V53i & V53e... -
Page 62: Support À La Clientele
Cette garantie couvre tous défauts dus aux matériaux et à la main d'œuvre quand le produit a été installé et utilisé en suivant les instructions écrites d'installation de Rinnai, dans les termes décrits dans ce document de garantie limitée. Cette garantie s'applique seulement aux produits qui sont installés correctement. - Page 63 Rinnai le remplacera par un produit comparable, à sa discrétion. Si un composant ou un produit retourné à Rinnai est trouvé sans défaut du aux matériaux ou à la main d'œuvre, ou qu'il est déterminé qu'il a été...
- Page 64 (VAM1620W, VB2020FFU) U287-1821(00) © 2010 Rinnai America Corporation Printed in Japan...