Inglesina TRILOGY Manuel D'instructions page 27

Masquer les pouces Voir aussi pour TRILOGY:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 29
LIST OF COMPONENTS
fig. 1
Chassis
T1 Front wheel assembly
T2 Std Trilogy rear wheel assemblies
T3 City Trilogy rear wheel assemblies
T4 Feeding bottle holder
T5 Storage basket
Transport Seat
R1 Handrail
R2 Pushchair seat hood
R3 Muff (if available)
R4 Rain cover (if available)
Carrycot
C1 Carrycot hood
C2 Carrycot apron
Infant Car Seat (if available)
CHASSIS
ASSEMBLY/REMOVAL OF REAR WHEEL ASSEMBLY
fig. 2
Insert the wheel assembly in correspondence of
the rear tube
fig. 3
Attach the ring (T6) to the bracket (T7), and press
the lever (T8) until it is fully attached, making sure that the
ring (T6) is properly positioned in its housing.
CAUTION: make sure that the wheels are properly
attached before use.
fig. 4
To remove the rear wheel assembly, lift the lever
(T8) and unhook the ring (T6) from the bracket (T7), until it is
completely free.
OPENING THE CHASSIS
fig. 5
Keeping pressed the lever (T9) positioned on the
right handle, firmly lift the frame until it is completely open.
fig. 6
Complete the procedure by pushing on the pedal
control (T10) until it is locked in horizontal position.
fig. 7
CAUTION:
make
mechanisms are properly attached on both sides before
use.
CLOSING THE CHASSIS
fig. 8
Press the button (T11) and lift the rear handle
(T12).
fig. 9
Firmly pull the rear handle (T12) upwards until the
chassis is completely folded
REAR WHEELS BRAKE
fig. 10
To engage the brake, push down the lever (T13)
positioned on the right rear wheel assembly
Always engage the brake during stops.
CARRY HANDLE
fig. 11
To transport the folded chassis, use the handle
(T14). Do not lift the chassis by the opening handle (T12).
BLOCKING/UNBLOCKING THE FRONT WHEELS
fig. 12
The chassis is equipped with swivel wheels, which
can be blocked/unblocked by means of the lever (T15)
located in correspondence of the central joint.
REMOVING THE FRONT WHEELS
fig. 13
If necessary, the front wheels can be easily
removed. To do so, push the lever (T16) forwards, as shown
in the figure and, simultaneously, remove the wheel.
fig. 14
To
reattach
the
correspondence of the opening (T17) and push until it clicks
into place.
sure
that
all
closing
wheels,
insert
them
in
CAUTION: make sure that the wheels are properly
attached before use.
REAR PLATFORM
fig. 15
Adjust the rear platform (T10) with your foot to
cross obstacles.
FEEDING BOTTLE HOLDER
fig. 16
The chassis is equipped with a standard feeding
bottle holder (T4).
To fasten the feeding bottle holder, place the upper guide in
correspondence of the hook (T18) on the chassis and push it
in its housing until it is fully attached.
STORAGE BASKET
fig. 17
The chassis is equipped with a capacious storage
basket (T5). To secure it, insert the eyelets (B1) onto the rear
hooks (T19) on the chassis.
Let the fins (B2) pass through the eyelets (T20) on the
side of the frame and fasten the corresponding press
studs.
Finally, insert the eyelets (B3) onto the front hooks (T21) on
the chassis
ADDITIONAL TRANSPORT UNITS (CARRYCOT, INFANT
CAR SEAT (if available), PUSHCHAIR SEAT)
fig. 18
The chassis can be used with the Trilogy carrycot,
the pushchair seat and the Huggy car seat (if available).
TRILOGY CARRYCOT
ATTACHING THE CARRYCOT TO THE CHASSIS
fig. 19
Take the carrycot from the handle and attach it to
the chassis in correspondence of the housings on both sides
of the structure and place it solely in rear facing position.
fig. 20
CAUTION: make sure that the carrycot is
properly attached before use.
DETACHING THE CARRYCOT FROM THE CHASSIS
fig. 21
Use the lever (C3) on the outside of the carrycot.
fig. 22
Simultaneously, lift the carrycot by holding it by the
handle.
ATTACHING THE HOOD
fig. 23
Fasten the press studs to the carrycot structure.
fig. 24
Wrap the hood (C1) around the handle, fastening it
by means of the press studs.
HANDLE AND HOOD ADJUSTMENT
fig. 25
To adjust the handle and the hood, press the two
buttons on the sides (C4) simultaneously.
fig. 26
CAUTION: to transport the carrycot, always hold
it by the handle.
HOOD VENTILATION (IF AVAILABLE)
fig. 27
The hood is equipped with a mesh netting that
allows for proper ventilation inside the carrycot.
ATTACHING THE APRON
fig. 28
Fasten all the apron buttons to the carrycot.
INTERNAL VENTILATION
fig. 29
Internal ventilation can be adjusted by means of
the lever (C5).
BACKREST ADJUSTMENT
fig. 30
Operate the lever (C6) to adjust the backrest: once the
desired position is reached, set the lever to the starting position.
MATTRESS
AND
MAINTENANCE
fig. 31
It is advisable to remove the mattress and internal
INTERNAL
LINING
27

Publicité

Table des Matières
loading

Table des Matières