HQ Power VDL1803MHRGB Mode D'emploi page 7

Display Description
Custom colour. See Manual Mode for more
ManualDimmer
information.
Note: At power-on, the device automatically enters DMX mode (the display shows <LED Addr:xxx>).
To set the device to stand-alone mode:
1. Connect nothing to the DMX input [4] of the device.
2. Press <SET/ESC> until <SET Menu> is displayed and press <ENTER>.
3. Use <UP> and <DOWN> to select <Master/Alone> and press <ENTER>.
4. Use <UP> and <DOWN> to select <Alone Mode> and press <ENTER>.
The indicator "Alone" will appear at the bottom right of the display when you choose the built-in program.
5. Use <UP> and <DOWN> to select <Auto/Sound> and press <ENTER>.
6. Use <UP> and <DOWN> to select the desired mode:
<Auto Mode> for normal mode. The indicator "Auto" will appear at the bottom left of the display when
o
you choose the built-in program.
<Sound Mode> for sound-activated mode. The indicator "Sound" will appear at the bottom left of the
o
display when you choose the built-in program.
7. Press <ENTER> to confirm.
8. Press <SET/ESC> until <LED xxx> is displayed.
9. Use <UP> and <DOWN> to select the desired program. The selected program starts automatically.
10. To activate pan/tilt movement with the program, press <ENTER>. The display shows <Motor Run>.
11. Press <ENTER>.
12. Use <UP> and <DOWN> to select <ON> and press <ENTER>.
The motor now starts moving the head.
Note: At power-on, the motor is deactivated for the programs.
Setting the Microphone Sensitivity
For sound-activated mode, you can adjust the sensitivity of the internal microphone. The default sensitivity
is 20%. To change the sensitivity of the internal microphone, proceed as follows:
1. Press <SET/ESC> until <SET Menu> is displayed and press <ENTER>.
2. Use <UP> and <DOWN> to select <MIC Sense> and press <ENTER>.
3. Use <UP> and <DOWN> to change the sensitivity (00 ~ 99%) and press <ENTER>.
Manual Mode
The manual mode (display: <LED Manual Dimmer>) allows you to define a custom colour by adjusting the
brightness of each LED colour (red, green, blue, white), and a precise head position by defining the exact pan
and tilt positions. You can also add a strobe effect, or even switch all the LEDs off.
1. Press <SET/ESC> until <LED xxx> is displayed.
2. Use <UP> and <DOWN> to select <LED Manual Dimmer> and press <ENTER>.
3. Use <UP> and <DOWN> to select the desired setting.
Refer to the table below for descriptions of the different settings:
Menu item
Light switch
Light red
Light green
Light blue
Light white
Light strobe
Scan pan
Scan tilt
Scan pan fine
Scan tilt fine
Light calibrate Password protected. Do not change these settings.
V. 01 – 26/10/2012
VDPL1803MHRGB
Setting Description
ON/OFF Select ON to switch the LEDs on. Select OFF to switch the LEDS off.
0 ~ 255 Set the brightness of the red LEDs.
0 ~ 255 Set the brightness of the green LEDs.
0 ~ 255 Set the brightness of the blue LEDs.
0 ~ 255 Set the brightness of the white LEDs.
0 ~ 255 Select one of various strobe effects.
0 ~ 255 Set the pan position.
0 ~ 255 Set the tilt position.
0 ~ 255 Fine-tune the pan position.
0 ~ 255 Fine-tune the tilt position.
Sound-activation
possible
no
7
Pan/tilt movement
possible
no movement, but
stationary pan/tilt
position is adjustable
©Velleman nv