HQ Power VDP900HZ Notice D'emploi page 4

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

4. Ins
tallation
• Remov
ve all packing m
remove
ed.
• Clean t
the spray nozzle
• Place t
he VDL900HZ
• Pour hi
igh quality smok
fluid lev
vel. Do not ove
• Connec
ct the remote co
5. Use
e
a) The
Device
• Plug th
he remote contro
power
cord.
• Turn on
n the power swi
• The red
d light on the re
• The de
vice must warm
minute
es.
• The gre
een light on the
Remot
te Control").
b) The
Remote Contr
Please re
efer the illustrat
1
pow
wer LED
smo
oke output ever
2
30
min)
3
out
put volume
4
fixe
ed time open LE
6. Not
tes
The V
VDP900HZ doe
pum
p will continue
• If you e
experience low
Check
the fluid level, t
working
g properly, plug
operati
ion to avoid per
before
transporting th
• Using t
the device will p
• A little
smoke may con
7. DMX
X Connectio
a. DMX5
12 Connection
Connect
an XLR cable to
pin XLR i
nput of the VDP
cable sho
ould be a two-co
b. DMX-5
512 Chain with
c. DMX S
Start Address
All DMX-c
controlled devic
This start
t address is the
Enter the
e correct numbe
You can u
use the same st
device.
09.11.201
0
aterial from the
e shipping box. C
e and make sure
e nothing is obs
horizontally on
a flat surface. R
ke liquid (VDLH
HLH5) into the t
rfill. Place the c
cap back on the
ontrol into the s
slot at the back
ol into the slot a
at the back of th
itch located at t
the back of the
emote control w
will light up.
m up. The period
d depends on th
e remote control
l will go up once
rol
ion on page 2.
ry x minutes (m
max.
ED
es not feature a
an automatic
e working. Alw
ways monitor t
device can su
uffer damage w
output, mechan
nical noise or no
the external fus
se, the remote c
g in the unit aga
ain. If the device
rmanent damag
e. Return the de
e unit.
produce water d
rops at the noz
ntinue to escape
e from the nozz
on
n
o the female 3-p
pin XLR output o
P900HZ. Multip
ple VDP900HZs
ore screened ca
able with XLR in
h Termination
n
A DMX term
minator is recom
to run a lon
g distance or is
The termina
ator prevents co
noise. The D
DMX terminator
between pin
ns 2 and 3, whic
the last dev
vice in the chain
ces need a digita
al start address
channel numbe
er from which th
er and read it fro
om the display
tarting address
for a whole gro
VDP90
0HZ
Check that all fo
structing the ou
Remove the liqu
tank, being care
liquid tank and
of the device.
he device. Plug
device.
he conditions bu
e the machine is
5
output LED
successive s
6
seconds)
7
heated over
8
spray button
stop function
the tank fluid
when run with
o output at all, u
control and the
e will not functi
evice to your de
zle. This is perf
zle after operatio
of your controlle
s can be linked
put and output
mmended for ins
in an electrical
orruption of the
is simply an XL
ch is then plugg
. Please see illu
so that the cor
he device starts
located on the b
oup of devices o
4
oam and plastic
c padding is
tput.
uid tank cap.
eful not to excee
ed the maximum
tighten.
the device into
the mains usin
ut should not tak
ke more than 10
s ready to opera
ate (see "The
spraying for x se
econds (max. 1
r LED
n
when running
g out of fluid; t
level during o
operation as th
hout fluid!
unplug the devi
ce immediately
power cord. If a
all appears to be
on after 30 seco
onds, discontinu
ealer. Remembe
er to drain the t
fectly normal.
on.
er and the other
r side to the ma
through serial l
inking. The link
connectors.
tallations where
e the DMX cable
ly noisy environ
nment (e.g. disc
digital control s
signal by electri
LR plug with a 1
120Ω resistor
ged into the XLR
R output socket
ustration.
rrect device resp
ponds to the sig
s to "listen" to th
he DMX controll
base of the VDP
P900HZ.
r enter an indiv
vidual one for ev
m
g the
0
5
the
he
.
e
ue
tank
ale 3-
king
e has
cos).
cal
of
gnals.
ler.
very
©Vellema
an nv

Publicité

Table des Matières
loading

Table des Matières