Taurus Alpatec ICE BIRSE Mode D'emploi page 7

ASSEMBLING THE BATTERIES
- Caution: During the handling of batteries, do
not touch both poles at the same time, as this
will provoke the partial discharge of the stocked
energy therefore affecting longevity.
- Remove the cover of the battery compartment.
- Check that the plastic covering that protects
the battery has been removed (some batteries
are sold with a protective covering)
- Put the battery in its compartment, respecting
the polarity.
- Replace the cover of the battery compartment.
ASSEMBLING THE FAN:
- Insert the bottom tube (P) into the hole on base
(Q), put the gasket (R) under the base and
tighten it with the L-shape screw (S) turning it
clockwise.
- Insert the top tube (N) to the bottom tube (P).
Align the bolt with the screw holes and tighten
the bolt (O).
- Insert the fan head (J) to the top tube (N). Align
the bolt with the screw holes and tighten the
bolt (L).
- Use the grill fasten nut (F) to attach the back
grill (G) to the fan head (J), and then use the
blade fasten nut (D) to attach the blades (E) to
the motor shaft (H).
- Attach the front grill (A) to the back grill (G).
Use the grill ring (B) to carefully hold them
together, and fasten the grill ring (B) with the
buckle and screw (C) provided.
- Check the correct rotation of the blades.
ADJUSTING THE HEIGHT:
- This fan has three working positions. You can
assemble it according to the height you desire.
- PEDESTAL: Follow all the intructions to assem-
ble the fan. The height will approximately be of
130cm.
- MIDDLE: Insert the fan head (J) directly to the
bottom tube (P). Align the bolt with the screw
holes and tighten the bolt (O). The height will
approximately be of 100cm.
- DESK: Insert the fan head (J) directly to the
base (Q). Put the gasket (R) under the base
and tighten it with the L-shape screw (S) turning
it clockwise. The height will approximately be
of 70cm.
INSTRUCTIONS FOR USE
BEFORE USE:
- Make sure that all products' packaging has
been removed.
- Prepare the appliance according to the function
you wish to use:
USE:
- Extend the cable completely before plugging
it in.
- Connect the appliance to the mains.
- Turn the appliance on, by using the on/off
button (3/c).
- The fan will start running at speed 2.
FAN FUNCTION:
- Select the desired ventilation speed by tou-
ching/pressing the speed selection button (2/a).
TIMER FUNCTION:
- The appliance's operating time can be control-
led (1-18h).
- To program the operating time with the remote
control, simply press the timer button (b) as
many times as hours you want to select. The
LED display (4) will show you the hours selec-
ted. When the display shows the speed again,
it means the timer has been confirmed. The
pilot light for the timer on the control panel (5)
will turn on.
- To program the operating time on the control
pannel, hold the oscillation button (a) for three
seconds. The LED display (4) will show a 0.
Touch the oscillaton button (a) as many times
as hours you want to select. The LED display
will show you the hours selected. When the dis-
play shows the speed again, it means the timer
has been confirmed. The pilot light for the timer
on the control panel (5) will turn on.
- After the selected time the appliance will switch
off automatically.
OSCILLATION FUNCTION:
- The oscillation function makes it possible to
direct the flow from the apparatus so that it
automatically alternates over a range of appro-
ximately 85º.
- To activate this function, press the oscillating
button (1/d).
- To deactivate this function, follow the procedu-
re for switching it on in reverse.