Maintenance Operations. Recommendations - gala gar SMART 200 MP Manuel Technique D'instructions

4. MAINTENANCE OPERATIONS. RECOMMENDATIONS.

In order for the equipment to have a long life we must
follow some essential rules for maintenance and use. Abide
by these recommendations.
CORRECT MAINTENANCE OF THE EQUIPMENT WILL
AVOID A GREAT PERCENTAGE OF FAULTS.
4.1 MACHINE MAINTENANCE. GENERAL 4.1 MACHINE MAINTENANCE. GENERAL
4.1 MACHINE MAINTENANCE. GENERAL 4.1 MACHINE MAINTENANCE. GENERAL
RECOMMENDATIONS. RECOMMENDATIONS.
RECOMMENDATIONS. RECOMMENDATIONS.
Before carrying out any operation on the machine or
welding cables, we must place the switch of the equipment
in "O" position of machine disconnected.
Specialized personnel must handle the machine to carry
out maintenance and repair operations.
BLOW THE INSIDE OF THE MACHINE WITH
COMPRESSED AIR FROM TIME TO TIME.
The accumulation of metal dust on the inside is one of the
main causes of breakdowns in this type of equipment as
they are subject to a great amount of pollution. As an
essential measure, the equipment must be kept separate
from the welding place, not placing it a short distance
away. Keeping the machine clean and dry is essential. The
inside must be blown as required. We must avoid any
anomaly or deterioration due to the accumulation of dust.
Blow the inside of the equipment with clean dry
compressed air. As routine to guarantee that the
equipment works correctly, check that once the machine
has been blown the electrical connections are still properly
tightened.
WARNING!: SEPARATE THE MACHINE WARNING!: SEPARATE THE MACHINE
WARNING!: SEPARATE THE MACHINE WARNING!: SEPARATE THE MACHINE
SUFFICIENTLY FROM THE WORKSTATION. SUFFICIENTLY FROM THE WORKSTATION. SUFFICIENTLY FROM THE WORKSTATION. SUFFICIENTLY FROM THE WORKSTATION.
PREVENT METAL DUST ENTERING THE EQUIPMENT.
LOCATE THE EQUIPMENT IN A PLACE
WHERE CLEAN AIR IS CONSTANTLY REPLACED.
The machine ventilations must be kept free. It must be
located in a place where clean air is renewed.
THE MACHINE MUST ALW THE MACHINE MUST ALWAYS BE OPERATED WITH
THE MACHINE MUST ALW THE MACHINE MUST ALW
THE HOUSING ON. THE HOUSING ON. THE HOUSING ON. THE HOUSING ON.
DO NOT DISCONNECT THE MACHINE IF IT
IS HOT.
If you have finished the work do not disconnect the
machine immediately, wait until the inner cooling system
has totally cooled it.
KEEP THE WELDING ACCESSORIES IN
GOOD CONDITIONS FOR USE.
ONCE THE WELDING OPERATION HAS
FINISHED AVOID DIRECT CONTACT OF THE
ELECTRODE-HOLDER CLAMP WITH THE
WELDING EARTH CLAMP AND THE OTHER PARTS
CONNECTED TO IT.
AYS BE OPERATED WITH
AYS BE OPERATED WITH AYS BE OPERATED WITH
SMART 200 MP
KEEP THE WELDING GUN IN GOOD
CONDITIONS FOR USE.
A damaged or worn gun can cause inefficient
welding.
WHEN FINISHING THE WELDING
OPERATION MAKE SURE THAT THE TORCH CATCH
IS UNLOCKED. (If mechanical lock guns are used)
4.2 RECOMMENDATIONS FOR REDUCING 4.2 RECOMMENDATIONS FOR REDUCING
4.2 RECOMMENDATIONS FOR REDUCING 4.2 RECOMMENDATIONS FOR REDUCING
ELECTROMAGNETIC COMPATIBILITY (CEM) ELECTROMAGNETIC COMPATIBILITY (CEM) ELECTROMAGNETIC COMPATIBILITY (CEM) ELECTROMAGNETIC COMPATIBILITY (CEM)
PROBLEMS. PROBLEMS. PROBLEMS. PROBLEMS.
The user is responsible for the installation and use of the
welding material according to the instructions in this
manual and the following recommendations.
Before installing the welding material, the presence of the
following in the surrounding area must be kept in mind:
•
Wiring for power, control, signalling, and telephones.
•
Radio and television receivers and transmitters.
•
Computers and other control equipment.
•
Critical security equipment.
•
People with pace makers or hearing aids.
•
Measurement and calibration equipment.
In order to reduce EMC problems, keep in mind the time
of day when welding or other activities will be carried out.
Move possible interference victims away from the welding
installation.
ALWAYS CONNECT THE MACHINE TO POWER
USING AN EFFICIENT EARTH TAP.
IF PROTECTIVE DEVICES OR SUPPLEMENTARY
ELECTRICAL SYSTEM FILTERS ARE NEEDED,
CONSULT OUR TECHNICAL SERVICE.
PERFORM THE MAINTENANCE OPERATIONS
USE THE SHORTEST WELDING WIRES POSSIBLE
AND KEEP THEM PLACED NEXT TO EACH OTHER
EQUIPMENT FORESEEN FOR USE IN INDUSTRIAL
ENVIRONMENT. ELECTROMAGNETIC DIFFICULTIES
MAY EXIST IN OTHER ENVIRONMENTS CAUSED BY
CONDUCTED AND RADIATED DISTURBANCES.
IF THE WELDING PIECE IS GROUNDED, KEEP IN
MIND OPERATOR SAFETY AND NATIONAL
DESCRIBED IN THIS MANUAL.
NEAR THE FLOOR.
REGULATIONS.
21