Intended Use - Makita DTW1001 Manuel D'instructions

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening capacities
Square drive
Drive shank
No load speed
Impacts per minute
Overall length
Rated voltage
For use near high-voltage electrical power lines
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for fastening bolts and nuts.
Model DTW800 / DTW800XV: The tool is also intended
for drilling into wood.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Model DTW1001
Sound pressure level (L
Sound power level (L ) : 109 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTW1002
Sound pressure level (L
Sound power level (L ) : 108 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTW800
Sound pressure level (L
Sound power level (L ) : 106 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Standard bolt
High tensile bolt
Hard impact mode
Medium impact mode
Soft impact mode
Hard impact mode
Medium impact mode
Soft impact mode
) : 98 dB(A)
pA
) : 97 dB(A)
pA
) : 95 dB(A)
pA
DTW1001 DTW1001XV DTW1002
M12 - M30
M10 - M24
19 mm
–
-
3.4 - 3.7 kg
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
WARNING:
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
4 ENGLISH
DTW1002XV DTW800
M12 - M24
M10 - M22
12.7 mm
11.1 mm Hex.
-1
0 - 1,800 min
-1
0 - 1,000 min
-1
0 - 900 min
-1
0 - 2,200 min
-1
0 - 2,000 min
-1
0 - 1,800 min
229 mm
D.C. 18 V
- -
3.3 - 3.6 kg 3.4 - 3.7 kg
DC18SH
Wear ear protection.
The noise emission during actual
Be sure to identify safety mea-
DTW800XV
–