Krups Aroma Partner Mode D'emploi page 13

STARTING AN AUTO START FUNCTION
„ Press the Preset time button (5) to set the time. Fig.12. The Preset time indicator
will appear on the display.
„ Set the time by pressing the HOURS button (2) to set the hour and the MINUTES
button (3) to set the minutes. To validate and exit the PROG mode, press
any button except the CLEAN button (6). the ON/OFF button (1). The time set is
automatically set after ten seconds.
„ Do not forget to fill the water tank and the coffee filter. The machine is now ready
to turn on automatically at preset time.
AUTO START FUNCTION WHEN TIME HAS ALREADY BEEN SET
„ To reactivate or check the preset time in memory, press Preset time button (5)
„ To cancel the saved auto-start program, press the Preset time button (5) for
3 seconds.
AFTER EACH CYCLE: CLEAN THE FILTER HOLDER AND CARAFE
„ Do not clean the machine if it's still hot.
„ To remove the used coffee grounds, remove the filter and the filter holder from
the coffee maker. Fig. 14.
„ Throw the coffee grounds and filter paper in the garbage.
„ Wash the filter holder in warm soapy water.
CAUTION: Do not place the carafe in the microwave. Do not put any parts of
the coffee maker into the dishwasher.
„ Clean the coffee maker with a damp cloth or sponge. Never use abrasive or
strong products on any part of the coffee maker.
„ To clean the stainless-steel parts of your coffee maker, dampen a soft cloth or
sponge with warm water. Wipe carefully with a dry cloth.For difficult stains, use
a cloth with white vinegar.
„ Do not immerse the appliance in water or under the tap.
WHEN THE GROUND COFFEE CONTAINER IS ALMOST EMPTY : CLEAN THE
GROUND COFFEE CONTAINER
„ Remove the ground coffee container's lid
„ If the container is still filled with coffee:
WITH A SPOON
„ Remove most of the coffee grounds with a spoon
WITH THE LEVER
„ Adjust the coffee strength to the maximum using the COFFEE STRENGTH
button (8)
„ Adjust the number of cups to the maximum using the CUP SELECTION button (7)
„ Pull the lever to let fall the coffee grounds
„ Repeat the operation if there's ground coffee in the filter remaining in the ground
coffee container
20
CLEANING
„ Remove the cone by pulling on it
„ Use the brush provided with the machine to remove the rest of the coffee
grounds
„ Carefully use a cloth to clean the ground coffee container
„ Put the cone back to it's position.
WHEN THE "CLEAN" LOGO BLINKS ON THE SCREEN OR WHEN YOU THINK
IT'S NECESSARY: DESCALE WITH CLEAN MODE
WHY DESCALE?
Limestone forms naturally in your coffee maker. Descaling preserves the coffee
maker and ensures it will last longer and provide quality coffee over time.
Limestone can permanently affect the machine's performance. Malfunctions
associated with scaling will not be covered by the guarantee if the product is
returned.
WHEN TO DESCALE?
When descaling is necessary, the CLEAN touch will light on. The descaling
frequency depends on the hardness of the water and the number of brew cycles.
If you notice the following signs: longer cycle time, excessive steaming, more
noise at the end of the cycle, stopping mid-cycle, this means your machine has
limestone build up and needs to be descaled.
Your coffee maker should be descaled around once a month depending on the
hardness of the water.
HOW TO DESCALE YOUR COFFEE MAKER
„ Use the KRUPS descaling solution or 0.5L of white vinegar diluted in 0.5L of
cold or water at room temperature Fig. 15.
„ Pour the solution into the water tank (without coffee in the filter). Fig 16.
„ Press the CLEAN button (6) to start the descaling cycle. Fig 17.
„ Wait until the end of the cycle.To rinse the machine, run 2 full 10-15 cups cycles
with clear water but without coffee.
„ Repeat the operation if needed.
THE GUARANTEE DOES NOT COVER COFFEE MAKERS THAT DO NOT
WORK, OR DO SO POORLY, DUE TO LACK OF DESCALING
21