General Information Concerning The Ce Marking - Hameg НМ6042 Manuel

G e n e r a l i n f o r m a t i o n c o n c e r n i n g t h e C E m a r k i n g
KONFORMITÄTSERKLÄRUNG
DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITE
DECLARACIÓN DE CONFORMIDAD
Hersteller / Manufacturer / Fabricant / Fabricante:
HAMEG Instruments GmbH · Industriestraße 6 · D-63533 Mainhausen
Die HAMEG Instruments GmbH bescheinigt die Konformität für das Produkt
The HAMEG Instruments GmbH herewith declares conformity of the product
HAMEG Instruments GmbH déclare la conformite du produit
HAMEG Instruments GmbH certifica la conformidad para el producto
Bezeichnung / Product name / Kennlinienschreiber / Curve Tracer
Designation / Descripción: Traceur de caractéristiques
Trazador de curvas
Typ / Type / Type / Tipo: HM6042
mit / with / avec / con:
Optionen / Options /
Options / Opciónes: –
mit den folgenden Bestimmungen / with applicable regulations /
avec les directives suivantes / con las siguientes directivas:
EMV Richtlinie 89/336/EWG ergänzt durch 91/263/EWG, 92/31/EWG
EMC Directive 89/336/EEC amended by 91/263/EWG, 92/31/EEC
Directive EMC 89/336/CEE amendée par 91/263/EWG, 92/31/CEE
Directiva EMC 89/336/CEE enmendada por 91/263/CEE, 92/31/CEE
Niederspannungsrichtlinie 73/23/EWG ergänzt durch 93/68/EWG
Low-Voltage Equipment Directive 73/23/EEC amended by 93/68/EEC
Directive des equipements basse tension 73/23/CEE amendée par 93/68/CEE
Directiva de equipos de baja tensión 73/23/CEE enmendada por 93/68/EWG
Angewendete harmonisierte Normen / Harmonized standards applied /
Normes harmonisées utilisées / Normas armonizadas utilizadas:
Sicherheit / Safety / Sécurité / Seguridad:
EN 61010-1:2001 (IEC 61010-1:2001)
Messkategorie / Measuring category / Catégorie de mesure / Categoría de
medida: I
Verschmutzungsgrad / Degree of pollution / Degré de pollution / Nivel de
polución: 2
Elektromagnetische Verträglichkeit / Electromagnetic compatibility /
Compatibilité électromagnétique / Compatibilidad electromagnética:
EN 61326-1/A1: Störaussendung / Radiation / Emission: Tabelle / table / tableau
4; Klasse / Class / Classe / classe B. Störfestigkeit / Immunity / Imunitee /
inmunidad: Tabelle / table / tableau / tabla A1.
EN 61000-3-2/A14: Oberschwingungsströme / Harmonic current emissions /
Émissions de courant harmonique / emisión de corrientes armónicas: Klasse /
Class / Classe / clase D.
EN 61000-3-3: Spannungsschwankungen u. Flicker / Voltage fluctuations and
flicker / Fluctuations de tension et du flicker / fluctuaciones de tensión y flicker.
Datum /Date /Date / Date
15. 07. 2004 Unterschrift / Signature / Signatur / Signatura
Manuel Roth
Manager
14
Subject to change without notice

General information concerning the CE marking

HAMEG instruments fulfill the regulations of the EMC directive.
The conformity test made by HAMEG is based on the actual
generic- and product standards. In cases where different limit
values are applicable, HAMEG applies the severer standard.
For emission the limits for residential, commercial and light
industry are applied. Regarding the immunity (susceptibility)
the limits for industrial environment have been used.
The measuring- and data lines of the instrument have much
influence on emmission and immunity and therefore on
meeting the acceptance limits. For different applications the
lines and/or cables used may be different. For measurement
operation the following hints and conditions regarding
emission and immunity should be observed:
1. Data cables
For the connection between instruments resp. their interfaces
and external devices, (computer, printer etc.) sufficiently
screened cables must be used. Without a special instruction
in the manual for a reduced cable length, the maximum cable
length of a dataline must be less than 3 meters long. If an
interface has several connectors only one connector must have
a connection to a cable.
Basically interconnections must have a double screening. For
IEEE-bus purposes the double screened cables HZ72S and
HZ72L from HAMEG are suitable.
2. Signal cables
Basically test leads for signal interconnection between test
point and instrument should be as short as possible. Without
instruction in the manual for a shorter length, signal lines
must be less than 3 meters long.
Signal lines must screened (coaxial cable - RG58/U). A proper
ground connection is required. In combination with signal
generators double screened cables (RG223/U, RG214/U) must
be used.
3. Influence on measuring instruments.
Under the presence of strong high frequency electric or
magnetic fields, even with careful setup of the measuring
equipment an influence of such signals is unavoidable.
This will not cause damage or put the instrument out of
operation. Small deviations of the measuring value (reading)
exceeding the instruments specifications may result from such
conditions in individual cases.
HAMEG Instruments GmbH