Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Connecting the outlet hose
The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 4).
The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
It is advisable to fit an anti-odour air trap
(fig. 4X).
If necessary the outlet hose can be
extended up to 2,5 m, provided that it is
kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.
4
Opening the door
Put your hand into the recess and pull.
If the machine comes open while it is working,
an electrical safety device automatically
switches everything off.
IMPORTANT
For the machine to work properly,
the door should not be opened while
it is in operation.
The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 4Y).
When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest possible
position under the worktop (fig. 4Z).
Check that there are no kinks in the inlet
and outlet hoses.
Closing the door
Place the baskets in the machine.
Make sure that both the spray arms are
free to rotate and are not obstructed by
cutlery, crockery or pans. Close the door,
pressing on it to make sure it is firmly shut.
34
WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special
regenerating
salt,
supplies
softened water for washing the dishes.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulating the water softener
The softener unit can treat water with a
hardness of up to 90°fH (French grading)
or 50°dH (German grading) through 6
different settings.
The table below lists different degrees of
water hardness with the corresponding
setting for the softener unit.
Water
hardness
0
0-5
0-3
NO
Position 1
6-15
4-9
YES
Position1
1
16-30
10-16
2
YES
Position 2
17-25
*3
31-45
YES
Position 3
46-60
26-33
4
YES
Position 4
5
61-90
34-50
YES
Position 5
* The water softener unit is set in the
factory at level 3, as this is suitable for
the majority of users.
According to the degree of hardness of
your water, regulate the softener unit in the
following way:
IMPORTANT
The dishwasher must be ALWAYS
off before start this procedure.
1. When the dishwasher is off, OPEN
the door.
2. Turn the programme selector to the
"UNIVERSAL" programme position.
3. Press the "ON/OFF" button.
4. WITHIN 15 seconds, turn the dial (in a
anti-clockwise direction) to the "RESET"
position then go to the "UNIVERSAL"
programme position again, doing this
4 times (finishing with the programme
selector on the "UNIVERSAL" programme
position).
5. The indicator light "WASHING" will
flash 3 times and the alarm will sound
3 times, to indicate the factory water
softener setting (LEVEL 3).
6. Turn the programme selector to one of
the inclusive positions among 1 and 5 to
choose the required water softener level.
7. The indicator light "WASHING" will
flash and the alarm will sound some
times, according to the select level (for
example, 5 times for the LEVEL 5).
8. Turn off the dishwasher pressing the
"ON/OFF" button to confirm the new
setting.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
Level 0/1
Level 2
Level 5
Level 3
("UNIVERSAL" programme)
Level 4
35
Publicité
Table des Matières
