Milwaukee 8975 Manuel De L'utilisateur page 2

GENERAL POWER TOOL SAFETY WARNINGS
WARNING
READ ALL SAFETY WARNINGS AND INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or
Save all warnings and instructions for future reference
serious injury.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of fl ammable
liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
• Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
• If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the infl uence of drugs, alcohol or medi-
cation. A moment of inattention while operating
power tools may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your fi nger on the switch or energising power
tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
• Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions
2
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
SERVICE
• Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
IMPORTANT SAFETY INSTRUCTIONS
HEAT GUNS
READ THESE INSTRUCTIONS
• Know your work environment. Hidden areas
such as behind walls, ceilings, fl oors, soffi t boards
and other panels may contain fl ammable materials
that may ignite when using the heat gun in these
locations. Ignition of these materials may not be
readily apparent and could result in property dam-
age and personal injury. Check these areas before
applying heat. If in doubt, use an alternate method.
Pausing or lingering in one spot may ignite the
panel or the material behind it. Keep heat gun
moving to avoid excessive temperatures.
• Do not direct the heat gun air airfl ow at clothing,
hair or other body parts. Do not use as a hair
dryer. Heat guns can produce 1000°F (540°C) or
more of fl ameless heat at the nozzle. Contact with
the air stream could result in personal injury.
• Do not use near fl ammable liquids or in ex-
plosive atmospheres, such as in the presence
of fumes, gases or dust. The fl ameless heat
from the heat gun may ignite the dust or fumes.
Remove materials or debris that may become
ignited from work area.
• Shield materials around the heated area to
prevent property damage or fi re.
• Keep a fi re extinguisher nearby. Heat guns may
ignite fl ammable materials left in the work area.
• WARNING! Hot Surfaces. Always hold the heat
gun by the plastic enclosure. Do not touch
nozzle, accessory tips or store heat gun until
the nozzle has cooled to room temperature.
The metal nozzle requires approximately 20
minutes to cool before it can be touched. Contact
with the nozzle or accessory tip could result in
personal injury. Place the heat gun in a clear area
away from combustible materials while cooling to
prevent fl ammable materials from igniting.
• Do not cut off airfl ow by placing nozzle too
close to workpiece. Keep intake vents clean
and clear of obstructions. Restricting airfl ow may
cause the heat gun to overheat.
• Place the heat gun on a stable, level surface
when not hand held. Use the support pads or
support stand. Place cord in a position that won't
cause the heat gun to tip over.
• Do not leave the heat gun unattended while
running or cooling down. Inattention invites
accidents.
• Store indoors in a dry location. Do not expose
to rain or moisture.
• Do not direct airfl ow directly on glass. The
glass may crack and could result in property
damage or personal injury.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE Service facility for a free
replacement.
• WARNING Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depend-
ing on how often you do this type of work. To
reduce your exposure to these chemicals:
work in a well ventilated area, and work with
approved safety equipment, such as those dust
masks that are specially designed to fi lter out
microscopic particles.
IMPORTANT SAFETY INSTRUCTIONS
FOR REMOVING PAINT
WARNING
Use extreme care when
stripping paint. Peelings, residue
and vapors of paint may contain lead,
which is POISONOUS. Pre-1977 paint
m a y c o n t a i n l e a d a n d p a i n t m a d e
before 1950 is likely to contain lead. Hand to
mouth contact with paint peelings or residue
from pre-1977 paint may result in lead
ingestion. Exposure to even low levels of lead
can cause irreversible brain and nervous
system damage. Young and unborn children
are especially vulnerable to lead poisoning.
DO NOT REMOVE LEAD-BASED PAINT WITH
A HEAT GUN. Before beginning your work,
determine whether the paint you are removing
contains lead. A local health department or
a professional who uses a paint analyzer
can check the paint for lead content. LEAD-
BASED PAINT SHOULD BE REMOVED ONLY
BY A PROFESSIONAL.
PERSONS REMOVING PAINT SHOULD
FOLLOW THESE GUIDELINES:
• Work in a well ventilated area. If possible, move
the workpiece outdoors. If working indoors, open
windows and place an exhaust fan in a window. Be
sure the fan is moving air from inside to outside.
Proper ventilation will reduce the risk of inhaling
chemicals found in the fumes or dust created by
using a heat gun.
3