Product Parts; Initial Assembly; Adjusting The Headrest - Cybex Silver PALLAS B2-FIX+LUX Manuel D'instructions

PRODUCT PARTS

EN
(a) User Guide Storage Compartment
(b) Backrest
(c) Adjustable Headrest
(d) Headrest Height Adjuster
(e) Booster
(f) Impact Shield
(g) Belt Guide Group 1
(h) Lap Belt Guide Group 2/3

INITIAL ASSEMBLY

Connect the backrest (b) to the booster (e) by hooking the guide lug on the
axis of the booster. The backrest (b) is then folded forward. Place the impact
shield (f) on the booster (e). Clip the L.S.P. (j) onto the marked area on the
side of the seat. Push until it clicks into the slots in the car seat shell.
THE CORRECT POSITION IN THE VEHICLE
The child seat with retracted ISOFIX Connect locking arms (k) can be used on
all vehicle seats with automatic three-point safety belts approved in the vehicle
manual for "universal" use.
A "semi-universal" certification is given to restraint systems that are connected
to the car through ISOFIX Connect locking arms (k). For this reason, ISOFIX
Connect can only be used in certain vehicles. Refer to the enclosed vehicle
type list for approved vehicles. You can obtain the most up-to-date version from
www.cybex-online.com.
In exceptional cases, the child car seat may also be used on the front
passenger seat. Always comply with the recommendations of the vehicle
manufacturer.
INSTALLING THE CHILD SEAT IN THE VEHICLE
1. Always ensure that...
• the backrests in the vehicle are locked in their upright position.
• when installing the child seat on the front passenger seat, adjust the vehicle
seat as far back as possible without affecting the belt routing.
2. Use the ISOFIX Connect adjustment handle (l) under the booster (e) and
pull the two ISOFIX Connect locking arms (k) to their furthest extent.
3. Now twist the ISOFIX Connect locking arms (k) 180° so that they are facing
the direction of the ISOFIX anchorage points (o).
6
(i) Shoulder Belt Guide
(j) Linear side impact protection (L.S.P)
(k) ISOFIX Connect Locking Arms
(l) ISOFIX Connect Adjustment
Handle
(m) ISOFIX Connect Release Button
(n) ISOFIX Connect Safety Indicator
(o) ISOFIX Anchorage Points
4. Place the child seat on the appropriate seat in the car.
5. Push the two locking arms (k) into the ISOFIX anchorage points (o) until
these lock into place with an audible "CLICK".
6. Use the ISOFIX Connect adjustment handle (l) and push the car seat
against the vehicle seat.
7. Ensure that the entire surface of the backrest of the child seat (b) is placed
against the backrest of the vehicle seat.
If the headrest of the vehicle is in the way, pull it upwards to its furthest
��
extent or remove it completely (except in rear-facing vehicle seats).
8. Ensure the seat is secure by trying to pull it out of the ISOFIX anchorage
points (o). The green safety indicators (n) must be clearly visible on both
sides of the seat.
9. In case the seat is used without ISOFIX connect, it can be stored away on
the bottom of the seat.
By using ISOFIX Connect, a connection to the vehicle is created which
��
increases your child's safety. Your child still needs to be secured with the
three-point belt of the vehicle and the impact shield for Group 1.
If the "Linear Side-impact Protection" (L.S.P.) is in conflict with the car door
��
or if it affects the space on the passenger seat, it is possible to detach it by
squeezing the top and bottom of the element and pulling it out of the slot
in the car seat shell. In order to put the L.S.P. back on the seat, clip it onto
the marked area on the side of the seat and push until it clicks into the slot.
REMOVING THE CHILD SEAT FROM THE VEHICLE
Perform the installation steps in the reverse order.
1. Unlock the ISOFIX Connect locking arms (k) on both sides by pushing
the release buttons (m) and pulling them back simultaneously.
2. Pull the seat away from the ISOFIX anchorage points (o).
3. Remove the child seat and store the ISOFIX Connect in reverse order
to installation.

ADJUSTING THE HEADREST

The headrest (c) can be adjusted by using the headrest height adjuster (d)
at the back of the headrest (c). Adjust the headrest so that max. 2 cm (approx.
2 finger's width) remain between the child's shoulder and the headrest (c).
The height of the headrest can still be adjusted while the seat is installed
��
in the car.