Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
GB
2.1 Stove setting
How to change the wished room temperature
Join the following procedure to change the wished temperature:
Press the key
(1) once to enter the menu and set temperature.
You will read the word "Set" and the wished temperature on the display.
Use the keys
(2) e
(3) to increase or reduce the wished value.
The stove will leave the menu Set temperature automatically as soon as you do not work
on it for some seconds.
How to change the working power
Join the following procedure to change the working power:
Press the key
(1) once to enter the menu and set the working power. You will read
the word "Pot" and the range of 5 possible powers on the display.
Use the keys
(2) and
(3) to increase or reduce the wished value.
The stove will leave the menu Set working power automatically as soon as you do not
use it for some seconds.
2.2 Suggestions
• Do not continuously turn the stove on and off as this could provoke sparks that could
shorten the life of the electrical components.
• Do not touch the stove with wet hands: the stove has electrical components that could
produce sparks if handled incorrectly. Only authorized technicians can resolve possible
problems.
• Never open the glass door of the pellet stove while the stove is in operation.
• Be sure that the brazier basket is positioned correctly.
some holes for inspection and cleaning.
2.3 How to load pellets in the tank
You can load pellets in the tank through the door on the upper part of the stove.
Join the following procedure to load pellets:
• Open the door on the upper part of the stove;
functioning of the stove);
• Close the door.
3.0 First Lighting of the Stove
3.1 Lighting the stove
• Fill the container 3/4 full with the pellets recommended by the manufacturer;
• Connect the stove to an electrical outlet with the cable that has been supplied;
• Press the lighting switch located on the back part of the stove;
• The upper display will read "OFF";
• Press the button
for 2 seconds. After a few moments the smoke extractor and
the lighting resistor will start and the display will read "
is switched on.
"
• After 1 minute the display will read
continue lighting the resistor;
• Once the appropriate temperature has been reached the display will read "
this means that the stove has begun the last phase in lighting, at the end of which the
stove will be completely operational; the led resistence is switched off.
• After several minutes of ventilation the display will read "ON 1-2-3-4-5" and the room
temperature, according to the power that has been programmed;
• Once the programmed temperature is reached the display will read "ECO" and the
room temperature;
• The temperature led lights when the programmed temperature is reached;
WARNING!
chamber.
3.2 Stove switching off
To switch off the stove, press the key
the display. After the stove has been switched off, the fan continues working for a set
time in order to grant a fast smokes exhaust from the combustion chamber.
If you have a model with remote control, you just need to switch the remote control off
SEND.
a switching off phase. Wait until the phase is completed and the key On/Off stops blinking
before starting up the stove again.
ACC.
"; the led resistence
LOAD PELL.
", the stove will load the pellets and
FIRE STAB.
on the control board until you read
This warns you that the stove is running
4.0 User menu
The board comes with a user/technician menu, accessible from the control panel. In this
the functions of automatic on / off (MN05 - MN06 - MN07 - MN08 - MN09 - MN10) are avai-
lable only by remote control.
The menu is divided as follows:
Menu
Description
MN01
Current day
MN02
Current hour
MN03
Current minutes
MN04
Access technical parameters
MN05
Timer ON 1
MN06
Timer OFF 1
MN07
Enabling TIMER1 ON/OFF
MN08
Timer ON 2
MN09
Timer OFF 2
MN10
Enabling TIMER2 ON/OFF
(*) See corresponding section
2
+
-
1
1
2
To enter the menu You must press key 1 and then the key 3 repeatedly.
Each time You press the button 3, the board changes by one position.
If you do not touch any key for at least 60 seconds, there is an automatic exit from menu.
4.1 Setting the time - MN01
SETTING the current day
• Press key 1 and then key 3 until the code MN01 is on display.
• Press key 1 and key 2 to change the day (key 1 for decrease, key 2 for increase).
• Set the desired days by referring the below table:
Abbreviation
DAY1
DAY2
DAY3
DAY4
DAY5
DAY6
DAY7
OFF
4.2 How to set current hour - MN02
":
• Press key 1 and then key 3 repeatedly until the code MN03 appears on the display.
• Press keys 1 and 2 to select the minutes. Hold the buttons to scroll faster.
4.3 How to set the current minutes - MN03
• Premere i tasti 1 e 2 per selezionare i minuti. Tenere premuto i pulsanti per scorrere
più velocemente.
CHRONOTHERMOSTAT –MN05 - MN06 - MN07 - MN08 - MN09 - MN10
The chronothermostat FUNCTION enables to programming automatic starts and stops
of the stove.
4.4 How to programm
Referring to the program 1
• Press key 1 and repeatedly key 3 until the code MN05 appears.
• Press the keys 1 and 2 to vary in steps of 10 minutes the time of automatic turn on.
"COOL"
on
Press and hold the buttons to scroll faster.
• Press key 1 and repeatedly key 3 until the code MN06 appears.
• Press the keys 1 and 2 to vary in steps of 10 minutes the time of automatic turn off.
Press and hold the buttons to scroll faster.
• Press key 1 and repeatedly key 3 until the code MN07 appears.
• To enable the function TIMER1 set MN07 "ON" by pressing key 2 the Timer LED and
this will light.
• To enable the function TIMER1 set MN07 "OFF" by pressing the key 2 the LED Timer,
in case the Timer 2 is not enabled, it will turn off.
Same procedure with the program 2, but You'll only use the codes MN08 - MN09 - MN10.
16
17
Schedule 1
Schedule 2
AL
3
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Available for
User
User
User
Technician (*)
User
User
User
User
User
3
Day
Publicité
Table des Matières
