Important - KRESS SBLR 2362 Mode D'emploi

1 ON/OFF switch with full wave electronic control and
adjusting wheel for speed selection
2 Holding button for continuous operation
3 Reversing switch
4 Switching from normal drilling to percussion drilling
5 Mains cable with patent quick-release lock
6 Locking device for mains cable module
7 Quick-change chuck
8 Auxiliary handle (optional accessory)
Technical data
Input
Output
Rotation right/left
No. of speed ranges
No-load speed r.p.m.
Load speed r.p.m.
Percussion rate p.m.
Max. drill dia. into steel mm
Max. drill dia. into wood mm
Max. percussion drill dia into
concrete mm
Max. screwing into wood mm
Max. screwing into
Sheet metal mm
Collar diameter, mm
Chuck dia., mm
Spindle thread
Weight kg
Use
This drill is universally suitable for use as a hammer drill
with stone, as a screwdriver with wood, metal and plastic,
and for cutting threads.
The drill is not suitable for heavy stirring or drilling
holes with large diameters.
Safety instructions and prevention of accidents
Before operating the machine, please read through the
operating instructions completely, follow the Safety
instructions in this manual as well as the general Safety
instructions for power tools in the accompanying
booklet.
Caution!
Beware of jamming. The machine may jam, for ex-
ample, when the machine is at an angle or when the
drill bit comes into contact with reinforcing steel!
Before fitting tools in the chuck or drill spindle dis-
connect the machine from the power supply, or re-
move the mains cable with patent quick-release lock
(5) from the grip using the locking device button (6)!
Do not work with materials containing asbestos!
Outside power sockets must be protected with
residual-current-operated circuit-breakers (r.c.c.b.).
Do not drill holes into the housing to label the
machine. The protective insulation will be bridged.
Please use self-adhesive labels.
Always lead cables away towards the back of the
machine.
Double insulation
Our equipment is designed in accordance with European
regulations (EN standards) for the utmost safety of the
user. Machines with double insulation always carry the
international symbol. The machines should not be
earthed. A two-core cable is sufficient.
The machines are interference-suppressed in accordance
with EN 55014.
Initial operation
Before the first operation check that the mains voltage cor-
responds to that given on the machine nameplate.
English
SBLR 2362/s
620 W
340 W
x
1
0–3400
1710
n x 16
13
30
16
6
6.3
43
13
1/2" x 20 UNF
1.7
Trigger switch with button for continuous operation
The machine is set in operation by pressing in the handle
switch (1). The small holding button (2) on the side of the
switch is pressed in for continuous operation. To release
the continuous operation merely depress the switch, which
makes the holding button spring back automatically.
Electronic speed control
This machine has an integrated full wave electronic control
circuit switch.
The required speed may be selected with the adjusting
wheel (e.g. for serial screw drilling or for cutting threads).
The switch is lockable in every position.
Position A = lowest speed
Position G = highest speed
Ensure that the drill is not allowed to jam for longer
than 2–3 seconds. Longer jamming can lead to motor
damage.

Important!

Continuous operation under strong load and low speed
can overheat the motor. Allow the motor to cool down
in no-load when set at a high speed!
Changing direction of rotation
(main rotation – clockwise)
The direction of rotation of the spindle is changed using
the reversing switch (3).
R = Clockwise (Right)
L = Anticlockwise (Left)
Important!
Press the reversing switch until it reaches the respec-
tive end position at the housing, i. e. until it can be felt
to engage!
The reversing switch is easiest to operate by using the
thumb and index or middle finger from both sides.
Attention!
Change direction of rotation only when the motor has
ceased turning!
When using the drill as a screwdriver, the percussion
mechanism must be switched off. Switch-over by
means of the sliding switch (4).
Percussion drilling device
The machine has an integrated percussion mechanism and
can be switched from normal drilling to percussion drilling.
The sliding switch (4) allows switching from normal drilling
to percussion drilling or vice-versa while the machine is in
operation.
Normal drilling position
Move slide switch (4) to the left in direction of normal
drilling.
Percussion drilling position
Move slide switch (4) to the right in direction of percussion
drilling.
Screwdriving
You can fit screwdriver bits directly into the drill chuck. For
best results use Phillips screws. Safe working is made
possible by the self-centering feature. Please be sure that
you also use the correct screwdriver bits.