Technical Specification - 3M 6000 Mode D'emploi

the inside of the face piece and nose cup inhalation
port(s). Install new valve(s) onto post(s). Be certain
valve is fully engaged under all three lugs on post,
lies flat, and spins freely on post.
Head Harness (6897) Replacement.
Unbuckle head harness straps and replace with
new head harness. Figure 11.
Lens Assembly (6898) Replacement.
Remove the two sets of screws using a screwdriver.
d
Then, pull the frame top and frame bottom away
from the faceseal. The frame top, frame bottom,
e
faceseal and the lens assembly have vertical line
markings that indicate their positions relative to one
another. Make certain these markings are aligned
for re-assembly. Figure 12.
Neck Strap (7883).
t
Connect loops at end of neck strap assembly onto
re
the face seal tabs at the top of the head harness.
y,
ACCESSORIES
Spectacle Kit (6878).
t. Install rail assembly into Face Piece with the plastic
foot positioned on centre port adapter and the top of
rail is centered between the lugs or projections at
top of face seal. Install frame assembly onto rail
assembly by inserting pins into holes in rubber
m slide. Spectacles can now be adjusted for optimal fit
and vision.
Lens Covers (6885).
Remove release liner from adhesive at each side of
e replacement Lens Cover. Position lens cover over
the Face Piece Lens and adhere in place. Remove
used lens cover by lifting tab away from face piece.
CLEANING AND DISINFECTION
Cleaning is recommended after each use. If the
respirator is to be used for more than one shift it
should be cleaned at the end of each shift and
stored between shifts in the original packaging or a
sealed container. To clean the respirator, the 3M™
ed
504 Wipe should be used to wipe the face seal of
the product. Remove the filters and disconnect the
air supply unit if appropriate. Clean parts (excluding
filters) by immersing in warm cleaning solution
(water temperature not to exceed 50°C), scrub with
soft brush until clean. Add neutral detergent if
e
necessary. Disinfect respirator by soaking in a
solution of quaternary ammonia disinfectant or
e
sodium hypochlorite or other disinfectant. Rinse in
d
clean, warm water and air dry at room temperature
ve
in a non-contaminated atmosphere.
at
CAUTION Do not use cleaners containing lanolin or
other oils on these products. Do not autoclave. Do
not use petrol, chlorinated degreasing fluids (such
as trichloroethylene), organic solvents or abrasive
cleaning agents to clean any part of the equipment.
Do not reassemble parts until facepiece is
completely dry.
STORAGE AND
TRANSPORTATION
These products should be stored in the packaging
provided in dry, clean conditions away from direct
sunlight, sources of high temperature, petrol and
solvent vapours. The original packaging is suitable
for transporting the product. When stored as stated,
the expected shelf life of the product is 5 years from
date of manufacture. Store in accordance with
manufacturer's instructions, see packaging.
End of Shelf Life
]
Temperature Range
\
Maximum Relative Humidity
,
The date of manufacture can be established by
examining the date clock on the inside of the
facepiece. Figure 13. The inner segment will display
the year, and the arrow will point to the month of
manufacture in the outer segment. The example
shows 01/09/2011 - 30/09/2011.
APPROVALS
These products are type approved and audited
annually by either: BSI Group The Netherlands B.V.
John M. Keynesplein 9, 1066 EP Amsterdam, The
Netherlands, Notified Body No. 2797. and / or BSI
Assurance UK Ltd, Kitemark Court, Davy Avenue,
Knowlhill, Milton Keynes MK5 8PP, UK, Notified
Body No. 0086. These products meet the
requirements of European Regulation (EU)
2016/425 and applicable local legislation. The
applicable European/local legislation and Notified
Body can be determined by reviewing the
Certificate(s) and Declaration(s) of Conformity at
www.3m.com/Respiratory/certs.
3M United Kingdom PLC, 3M Centre, Cain Road,
Bracknell, RG12 8HT, 08706080060.
Dispose in accordance with local regulations

TECHNICAL SPECIFICATION

Respiratory Protection EN136 (Class 1) - for use
with 3M Filters (bayonet) to EN14387:2004 or
EN143:2000 and AS/NZS 1716:2012 (see
165
Re
res
ex
Re
pro
ac
me
co
sta
Ma
(AP
on
pro
ma
ap
Ple
nu
fur
Ey
(In
Sp
pro
ag
Flo
Ma
l/m
Ma
Ma
CA
eq
mo