Modine CW 002 Manuel D'installation Et D'entretien page 7

MECHANICAL SPECIFICATIONS / UNIT
Dampers (optional equipment)
When specified, the unit shall be equipped with a 25% or 100%
galvanized steel fresh air blade damper. Model C, floor units
only.
When dampers are specified, indicate one of the following:
1. These dampers shall be controlled from the end pocket
with a manual control assembly that indicates the open and
closed positions.
2. The damper shall be controlled by an electric, spring-return
type motor, which will be energized when the blower motor
is turned on thus moving the damper to the 25% or 100%
position. It will be de-energized and close the damper when
the blower motor is off.
Table 7.1
1 & 2 Row Unit Data Specifications
Unit Size
Coil
Standard – 1 Row Face Area, Ft.2
High Capacity – 2 Row Face Area, Ft.2
Standard Coil Connections . . . . . . . . .
High Capacity Coil Connections . . . . . . . . .
Blowers (Direct Drive)
No./Dia. x Width (Inches) . . . . . . . . . . . . .
Standard PSC Motor Data
High Speed (RPM) . . . . . . . . . . . . . . . . .
Low Speed (RPM) . . . . . . . . . . . . . . . .
High CFM . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low CFM . . . . . . . . . . . . . . . . . . . . . . . . .
Motor HP . . . . . . . . . . . . . . . . . . . . . .
Volts/Phase/Hertz . . . . . . . . . . . . . . . . . . . .
Amps, Standard PSC Motor . . . . . . . . . . . .
Standard EC Motor Motor Data
High Speed (RPM) . . . . . . . . . . . . . . . . .
Medium Speed (RPM) . . . . . . . . . . . . . . . .
Low Speed (RPM) . . . . . . . . . . . . . . . .
High CFM . . . . . . . . . . . . . . . . . . . . . . . . . .
Medium CFM . . . . . . . . . . . . . . . . . . . . . . .
Low CFM . . . . . . . . . . . . . . . . . . . . . . . . .
Motor HP . . . . . . . . . . . . . . . . . . . . . .
Volts/Phase/Hertz . . . . . . . . . . . . . . . . . . . .
Amps, Standard EC Motor . . . . . . . . . . . . . .
Shipping Weight – Lbs.
Model C . . . . . . . . . . . . . . . . . . . . . . . . . .
Model CW . . . . . . . . . . . . . . . . . . . . . . . . .
* Amp values are maximum based on motor name plate data
* Standard solid state speed control offers infinite speed control between high and low speed/CFM on standard PSC motor.
* Three speed switch offers high, medium & low speed/CFM on standard EC motor
* Sizes 002-006 have one motor. Sizes 008-014 have two motors.
Motors, Blowers and Drives
Blowers shall be of the centrifugal, forward curved type, to
provide even air distribution and low sound level.
All units shall have permanent split capacitor (electronically
communicated motor) available when specified as optional
equipment) direct-drive motors. The motor and blower
assembly shall be capable of being easily removed from the
unit. Motors are built for continuous duty to NEMA standards.
Grilles (optional equipment)
When specified, aluminum linear bar inlet and/or outlet grilles
shall be provided.
When specified, outlet grilles may have two-way deflection louvers.
Filters
All air, both fresh and return, shall be filtered by a cleanable
expanded aluminum filter.
002 003 004
1.0 1.3 1.6
1.1 1.5 1.8
7/8" I.D 7/8" I.D 7/8" I.D
Sweat Sweat Sweat
5/8" ID 5/8" ID 5/8" ID
Sweat Sweat Sweat
1 / 5-1/4 1 / 5-3/4 2 / 5-1/4
x 7 x 7 x 7
1050 1050 1050
625 625 625
250 330 450
150 195 270
1/30 1/30 1/20
115/1/60 115/1/60 115/1/60
0.7 0.7 1.05
1050 1050 1050
840 840 840
625 625 625
250 330 450
200 265 360
150 195 270
0.25 0.25 0.25
115/1/60 115/1/60 115/1/60
3.7 3.7 3.7
80 90 110
90 100 120
11-500.7
006 008 010
2.3 3.4 3.4
2.7 3.6 3.6
7/8" I.D 1-1/8" 1-1/8"
Sweat Sweat Sweat
5/8" ID 1-1/8" 1-1/8"
Sweat Sweat Sweat
2 / 5-3/4 3 / 5-3/4 3 / 5-3/4
x 7 x 7 x 7
1050 1050 1050
625 625 625
620 840 1050
370 545 685
1/20 1/30 1/20 1/30 1/20 1/20 1/20 1/20 1/20
115/1/60 115/1/60 115/1/60
1.05 1.75 1.75
1050 1050 1050
840 840 840
625 625 625
620 840 1050
495 695 870
370 545 685
0.25 0.5 0.5
115/1/60 115/1/60 115/1/60
3.7 7.4 7.4
120 160 165
130 170 175
012 014
4.6 4.6
4.8 4.8
1-1/8" 1-1/8"
Sweat Sweat
1-1/8" 1-1/8"
Sweat Sweat
4 / 5-3/4 4 / 5-3/4
x 7 x 7
1050 1050
625 625
1240 1430
805 930
115/1/60 115/1/60
2.1 2.1
1050 1050
840 840
625 625
1240 1430
1025 1180
805 930
0.5 0.5
115/1/60 115/1/60
7.4 7.4
185 190
195 200
7