Dremel 8000 Traduction De La Notice Originale page 17

PICTURE 2
A. Collet Nut
B. Collet
C. Housing Cap
D. Shaft Lock Button
E. Softgrip
F. Ventilation Openings
G. On/Off Switch and Variable Speed Dial
H. Fuel Gauge
I. Release Tab
J. Battery
K. Charger
CHARGING THE TOOL
The Cordless Rotary Tool is not fully charged. The tool is equipped
with a removable battery pack. Be sure to charge pack prior to
initial use.
To charge the tool:
1. Put the switch in the "OFF" position. PICTURE 2
2. Squeeze the release tabs on both sides of the battery pack
and remove pack from back of tool. PICTURE 2
3. Align exterior shape of battery pack with exterior shape of
charger (arrows on battery will point to the arrows located
on charger), squeeze release tabs, insert battery pack into
charger and release pressure on tabs so it locks in place.
4. Plug charger into the power source. The green LED light
indicates connection has been made and the battery pack is
charging. Under normal use the tool requires 3 hours charging
time to reach full capacity. When charging is complete, LED
on charger will turn off.
5. When charging is completed, squeeze release tabs and
remove battery pack from charger.
6. Align exterior shape of battery pack with exterior shape of the
housing of tool. Squeeze release tabs, insert battery pack into
back of tool and release so it locks in place."
IMPORTANT CHARGING NOTES
1. The battery pack accepts only about 80% of its maximum
capacity with its first few charge cycles. However, after the
first few charge cycles, the battery will charge to full capacity.
2. The charger was designed to fast charge the battery only
when the battery temperature is between 4ºC and 41ºC.
3. A substantial drop in operating time per charge may mean
that the battery pack is nearing the end of its life and should
be replaced.
NOTE: Use of chargers or battery packs not sold by Dremel will void
the warranty.
855-01 / 1.0Ah
2610919993
855-02 / 1.3Ah
2610944356
2610919971 (EU) / 2610943968 (EU) /
2610920898 (UK) 2610943969 (UK)
3 hrs. 2 hrs.
5 hrs. 3 hrs.
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identified by the rings on the back of the collet.
PICTURE 3
L. 3.2 mm Collet without ring (480)
M. 2.4 mm Collet with three rings (481)
N. 1.6 mm Collet with two rings (482)
O. 0.8 mm Collet with one ring (483)
NOTE: Some multitool kits may not include all four collet sizes.
Collets are available separately.
Always use the collet that matches the shank size of the accessory
you plan to use. Do not force a larger diameter shank into a smaller
collet.
CHANGING COLLETS
PICTURE 4
P. Shaft Lock Button
Q. Collet Wrench
R. To tighten
S. To loosen
T. Collet Nut
1. Press the shaft lock button, hold down and rotate the shaft
by hand until it engages the shaft. Do not engage the shaft
lock button while multitool is running.
2. With the shaft lock button engaged, loosen and remove the
collet nut. Use the collet wrench if necessary.
3. Remove the collet by pulling it free from the shaft.
4. Install the appropriate size collet fully into the shaft and
reinstall the collet nut finger tight. Do not fully tighten the
nut when there is no bit or accessory installed.
CHANGING ACCESSORIES
PICTURE 4/5
P. Shaft Lock Button
1. Press the shaft lock button and rotate the shaft by hand
until it engages the shaft lock. Do not engage the shaft lock
button while multitool is running.
2. With the shaft lock button engaged, loosen (do not remove)
the collet nut. Use the collet wrench if necessary.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock button engaged, finger tighten the collet
nut until the bit or accessory shank is gripped by the collet.
Use the collet wrench to secure the bit or accessory in the
collet.
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
17
COLLETS