Dremel 8000 Traduction De La Notice Originale page 16

support the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be different from
grinding wheel flanges.
d. Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for the
higher speed of a smaller tool and may burst.
ADDITIONAL SAFETY WARNINGS SPECIFIC
FOR ABRASIVE CUTTING OFFOPERATIONS
a. Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth of
cut. Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut
and the possibility of kickback or wheel breakage.
b. Do not position your body in line with and behind the rotating
wheel. When the wheel, at the point of operation, is moving
away from your body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
c. When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of wheel
binding.
d. Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully reenter the cut.
The wheel may bind, walk up or kickback if the power tool
is restarted in the workpiece.
e. Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback. Large workpieces tend
to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
f. Use extra caution when making a "pocket cut" into existing
walls or other blind areas. The protruding wheel may cut gas
or water pipes, electrical wiring or objects that can cause
kickback.
SAFETY WARNINGS SPECIFIC FOR SANDING
OPERATIONS
a. When sanding, do not use excessively oversized sanding
disc paper. Follow manufacturers recommendations, when
selecting sanding paper. Larger sanding paper extending
beyond the sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc, or kickback.
SAFETY WARNINGS SPECIFIC FOR POLISHING
OPERATIONS
a. Do not allow any loose portion of the polishing bonnet or
its attachment strings to spin freely. Tuck away or trim any
loose attachment strings. Loose and spinning attachment
strings can entangle your fingers or snag on the workpiece.
SAFETY WARNINGS SPECIFIC FOR WIRE
BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b. If the use of a guard is recommended for wire brushing, do
not allow any interference of the wire wheel or brush with
the guard. Wire wheel or brush may expand in diameter due
to work load and centrifugal forces.
ENVIRONMENT
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EC COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately
and disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating
. . . . . . . . . . . . . . .
Amperage Rating
. . . . . . . . . . . .
No Load Speed
. . . . . . . . . . . . . . .
Collet Capacity
. . . . . . . . . . . . . . .
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range of
Dremel accessories and attachments allow you to perform a large
variety of tasks. These include tasks such as sanding, carving and
engraving, cutting, cleaning and polishing.
PICTURE 1
16
DISPOSAL
10.8V
1.3Ah
n 35.000/min
o
0.8mm, 1.6mm, 2.4mm, 3.2mm
GENERAL