Mitsubishi Electric CITY MULTI PWFY-P100VM-E-BU Mode D'emploi page 12

How to Set the Simple Timer
1. Be sure that you are at a standard control screen, and that the simple timer indi-
cator is visible in the display (at A).
When something other than the Simple Timer is displayed, set it to SIMPLE
TIMER using the function selection of remote controller (see 3.[3]–3 (3)) timer
function setting.
2. Press the TIMER MENU button b, so that the "Set Up" appears on the screen
(at B). (Note that each press of the button toggles the display between "Set Up"
and "Monitor".)
3. Press the ON/OFF button 1 to display the current ON or OFF simple timer set-
ting. Press the button once to display the time remaining to ON, and then again to
display the time remaining to OFF. (The ON/OFF indication appears at D).
• "ON" timer: The unit will start operation when the specified number of hours
has elapsed.
• "OFF" timer: The unit will stop operation when the specified number of hours
has elapsed.
4. With "ON" or "OFF" showing at C: Press the appropriate Set Time button a as
necessary to set the hours to ON (if "ON" is displayed) or the hours to OFF (if
"OFF" is displayed) at D.
• Available Range: 1 to 72 hours
5. To set both the ON and OFF times, repeat Steps 3 and 4.
* Note that ON and OFF times cannot be set to the same value.
6. To clear the current ON or OFF setting: Display the ON or OFF setting (see step
3) and then press the CHECK (CLEAR) button 0 so that the time setting clears
to "—" at D. (If you want to use only an ON setting or only an OFF setting, be
sure that the setting you do not wish to use is shown as "—".)
7. After completing steps 3 to 6 above, press the CIR.WATER
the value.
Note:
Your new settings will be cancelled if you press the Mode (Return) button 2 before
pressing the CIR.WATER button 4.
8. Press the Mode (Return) button 2 to return to the standard control screen.
9. Press the TIMER ON/OFF button 9 to start the timer countdown. When the
timer is running, the timer value is visible on the display. Be sure that the timer
value is visible and appropriate.
Viewing the Current Simple Timer Settings
1. Be sure that the simple timer indicator is visible on the screen (at A).
2. Press the TIMER MENU button b, so that the "Monitor" appears on the screen
(at E).
• If the ON or OFF simple timer is running, the current timer value will appear at
F.
• If ON and OFF values have both been set, the two values appear alternately.
3. Press the Mode (Return) button 2 to close the monitor display and return to the
standard control screen.
12
Timer Setting
Action (On or Off)
* "— —" is displayed if there is
no setting.
button 4 to lock in
Timer Setting
To Turn Off the Simple Timer...
Press the TIMER ON/OFF button 9 so that the timer setting no longer appears on
the screen (at G).
To Turn On the Simple Timer...
Press the TIMER ON/OFF button 9 so that the timer setting becomes visible at G.
Examples
If ON and OFF times have both been set at the simple timer, operation and display
are as indicated below.
Example 1:
Start the timer, with ON time set sooner than OFF time
ON Setting: 3 hours
OFF Setting: 7 hours
Example 2:
Start the timer, with OFF time is sooner than ON time
ON Setting: 5 hours
OFF Setting: 2 hours
At Timer Display shows the timer's ON
setting (hours remaining to
Start
ON).
Display changes to show the
At 3 hours
after timer timer's OFF setting (hours
start remaining to OFF).
The time displayed is OFF
setting (7 hours) – ON setting
(3 hours) = 4 hours.
At 7 hours
The unit goes off, and will
remain off until someone
after timer
restarts it.
start
At Timer Display shows the timer's
OFF setting (hours remaining
Start
to OFF).
At 2 hours Display changes to show the
after timer timer's ON setting (hours
remaining to ON).
start
The time displayed is ON set-
ting (5 hours) – OFF setting (2
hours) = 3 hours.
At 5 hours
The unit comes on, and will
after timer continue to run until someone
turns it off.
start