Maintenance And Care - Flex LST 803 VR Mode D'emploi

klqb
fí=áë=êÉÅçããÉåÇÉÇ=íç=ìëÉ=~=cibu=`ä~ëë=j=
ëéÉÅá~ä=Éñíê~ÅíçêK
 Take the hose included in delivery and
pull the end without an adapter through
the hose holder and connect to the con-
nector (1.). Check the attachment!
 Connect extraction hose of the extraction
system to the adapter.
Follow the operating instructions for the
dust extraction system!
Check the attachment! If required, use
an appropriate adapter.
klqb
fÑ=óçìê=Çìëí=Éñíê~Åíçê=êÉèìáêÉë=~=ëéÉÅá~ä=ÅçåJ
åÉÅíáçå=EáKÉK=~=ÅçååÉÅíáçå=çíÜÉê=íÜ~å=
íÜÉ=PO=ããLPS=ãã=ëí~åÇ~êÇ=ÅçååÉÅíáçå=
ïÜáÅÜ áë=áåÅäìÇÉÇ=ïáíÜ=íÜÉ=ÉäÉÅíêáÅ=éçïÉê=íççäFI=
Åçåí~Åí=óçìê=Çìëí=Éñíê~Åíçê=ëìééäáÉê=íç=çÄí~áå=
íÜÉ=~ééêçéêá~íÉ=~Ç~éíÉêK
Operating instructions
t^okfkd>
qÜÉ=ãáääáåÖ=ÜÉ~Ç=ãìëí=åçí=ÅçãÉ=áåíç=Åçåí~Åí=
ïáíÜ=ëÜ~êé=éêçàÉÅíáåÖ=çÄàÉÅíëK=a~åÖÉê=çÑ=âáÅâJ
Ä~Åâ>=a~ã~ÖÉ=íç=ãáääáåÖ=ÜÉ~ÇK=
fÑ=íÜÉ=ãáääáåÖ=ÜÉ~Ç=áë=Ç~ã~ÖÉÇ=çê=ëÉîÉêÉäó=
ïçêåI=áí=ãìëí=ÄÉ=êÉéä~ÅÉÇK
`^rqflk>
eçäÇ=íÜÉ=ÉäÉÅíêáÅ=éçïÉê=íççä=ïáíÜ=ÄçíÜ=Ü~åÇë>=
20
Bush hammering machine LST 803 VR, LST 1503 VR
1. If required, set working width.
2. If required, set side stop.
3. Connect dust extraction system.
4. Insert mains plug.
5. Conduct a test run to check that the tool
is attached correctly.
Switch on the electric power tool (without
locking the button) and leave it running
for approx. 30 seconds.
Check for imbalances and vibrations.
6. Set required speed.
7. Switch on dust extraction system.
8. Hold the electric power tool with both
hands.
9. Switch on the device.
 Do not leave the electric power tool running
too long in one place.
 Always perform smooth stroke move-
ments.
 Observe a minimum distance of 1 cm from
the edge of the processed material.

Maintenance and care

t^okfkd>
_ÉÑçêÉ=éÉêÑçêãáåÖ=~åó=ïçêâ=çå=íÜÉ=ÉäÉÅíêáÅ=
éçïÉê=íççäI=éìää=çìí=íÜÉ=ã~áåë=éäìÖK