Berner BAGX 125 1300W Notice Originale page 22

The vibration level given in these instructions has
been measured in accordance with a standard-
ised measuring procedure and may be used to
compare power tools. It can also be used for a
preliminary estimation of exposure to vibration.
The stated vibration level applies to the main ap-
plications of the power tool. However, if the power
tool is used for different applications, with differ-
ent application tools or poorly maintained, the vi-
bration level may differ. This can significantly in-
crease the exposure to vibration over the total
working period.
To estimate the exposure to vibration accurately,
the times when the tool is switched off or when it
is running but not actually being used should also
be taken into account. This can significantly re-
duce the exposure to vibration over the total work-
ing period.
Implement additional safety measures to protect
the operator from the effects of vibration, such as
servicing the power tool and application tools,
keeping the hands warm, and organising work-
flows correctly.
Fitting
English
Fitting protective equipment
Pull the plug out of the socket before carry-
u
ing out any work on the power tool.
Note: If the grinding disc breaks during operation
or the holding fixtures on the protective guard/
power tool become damaged, the power tool
must be sent to an after-sales service agent for
maintenance.
Protective guard for grinding
power tool and rotate the protective guard until it
audibly clicks into place.
Adjust the position of the protective guard (7) to
meet the requirements of the operation. To do
this, push the unlocking lever (1) upward and ro-
tate the protective guard (7) into the required pos-
ition.
22 | English
English
English
Place the protective
guard (7) onto the
holder on the power
tool until the coding
cams of the protective
guard are aligned with
the holder. When do-
ing so, press and hold
the unlocking lever (1).
Press the protective
guard (7) onto the
spindle collar until the
shoulder of the pro-
tective guard is sitting
on the flange of the
Always position the protective guard (7) such
u
that all three red cams on the unlocking lever
(1) engage in the corresponding openings on
the protective guard (7).
Adjust the protective guard (7) such that
u
sparking in the direction of the operator is
prevented.
The protective guard (7) must only be ad-
u
justable while the unlocking lever (1) is actu-
ated. Otherwise, the power tool must not be
used any more under any circumstances and
must be sent to the after-sales service.
Note: The coding cams on the protective guard
(7) ensure that only a protective guard that is suit-
able for the power tool can be fitted.
Protective guard for cutting
Always use the protective guard for cutting
u
(9) when cutting bonded abrasives.
Provide sufficient dust extraction when cut-
u
ting stone.
The protective guard for cutting (9) is fitted in the
same way as the protective guard for grinding (7).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide
block (18) is fitted in the same way as the protect-
ive guard for grinding (7).
Side handle
English
Do not operate your power tool without the
u
side handle (6).
Screw the side handle (6) on the left or right of
the machine head depending on how your are
working.
Low-vibration auxiliary handle
and more comfortably.
Do not make any alterations of any kind to
u
the auxiliary handle.
Do not continue to use a damaged auxiliary
handle.
Hand guard
English
Always fit the hand guard (14) when working
u
with the cup brush/disc brush (15) or diamond
core cutter (20).
Attach the hand guard (14) to the auxiliary handle
(6).
Fitting and removing abrasive tools
Pull the plug out of the socket before carry-
u
ing out any work on the power tool.
English
English
English
The low-vibration auxil-
iary handle reduces vi-
bration, enabling the
tool to be used safely
English
1 609 92A 4ZV • 9.4.19