Product Description And Specifications; Intended Use; Product Features - Berner BAGX 125 1300W Notice Originale

Support panels or any oversized workpiece to
u
minimize the risk of wheel pinching and kick-
back. Large workpieces tend to sag under
their own weight. Supports must be placed un-
der the workpiece near the line of cut and near
the edge of the workpiece on both sides of the
wheel.
Use extra caution when making a "pocket
u
cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can
cause kickback.
Safety Warnings specific for Sanding
operations
English
Do not use excessively oversized sanding
u
disc paper. Follow manufacturers recom-
mendations, when selecting sanding paper.
Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc, or
kickback.
Safety Warnings specific for Wire Brushing
operations
English
Be aware that wire bristles are thrown by the
u
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush The wire bristles can easily
penetrate light clothing and/or skin.
If the use of a guard is recommended for wire
u
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire
wheel or brush may expand in diameter due to
work load and centrifugal forces.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if utility
u
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage or may cause an electric shock.
Do not touch grinding and cutting discs until
u
they have cooled down. The discs can be-
come very hot while working.
Release the On/Off switch and set it to the
u
off position when the power supply is inter-
rupted, e. g., in case of a power failure or
when the mains plug is pulled. This prevents
uncontrolled restarting.
Secure the workpiece. A workpiece clamped
u
with clamping devices or in a vice is held more
secure than by hand.
Products sold in GB only:
20 | English
Your product is fitted with an BS 1363/A ap-
proved electric plug with internal fuse (ASTA ap-
proved to BS 1362).
If the plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in
its place by an authorised customer service agent.
The replacement plug should have the same fuse
rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inser-
ted into a mains socket elsewhere.
Product Description and
Specifications
Please observe the illustrations at the beginning
of this operating manual.

Intended use

The power tool is intended for roughing metal,
stone and ceramic materials and for drilling tiles.
With approved abrasive tools, the power tool can
be used for sanding with sanding discs.
A special protective guard for cutting must be
used when cutting bonded abrasives.
Sufficient dust extraction must be provided when
cutting stone.
Together with the hand guard (accessory), the
English
power tool can be used for brushing and sanding
with elastic sanding pads.
The power tool is suitable only for working without
water.

Product features

The numbering of the product features refers to
the diagram of the power tool on the graphics
page.
(1) Unlocking lever for protective guard
(2) Direction of rotation arrow on housing
(3) Lever
(4) On/off switch
(5) Speed preselection thumbwheel
(6) Auxiliary handle (insulated gripping surface)
(7) Protective guard for grinding
(8) X-LOCK grinding disc/flap disc
(9) Protective guard for cutting
(10) X-LOCK cutting disc
English
Read all the safety and general in-
structions. Failure to observe the
safety and general instructions may
result in electric shock, fire and/or ser-
ious injury.
English
English
(BAGX 125 1700W)
A)
1 609 92A 4ZV • 9.4.19
A)
A)