BOMANN KA 1360 CB Mode D'emploi page 21

Electrical Connection

NoTE:
Please ensure that the device is switched off. The switch must
be on „0".
Insert the mains plug into a properly installed 230 V, 50 Hz
socket with earthing contact. For information please see the type
plate on the device.
operation
• Fold open the water tank lid.
• Now fill cold water for the desired number of cups into the
rear water container, as shown on the water level indicator.

NoTE: You can use the pot to fill the water tank.
CAUTIoN:
Do not overfill the tank! Do not fill it above the MAX mark.
• Then screw the lid on to the pot in such a way that the but-
ton on the lid is pointing towards the handle.
• Turn over the lower fold of the paper filter (size 1x4) and
place it in the filter funnel. Then fill it with coffee powder.
• Close the lid of the water tank until it is heard to click into
place.
• With the lid screwed in place, place the pot on the stand.
CAUTIoN: ANTI-DRIP SySTEM
Please ensure that the lid is on the pot. This activates the
so-called anti-drip system.
• Your device has an anti-drip system. If the pot is
removed before all of the water has passed through
the filter, this prevents the coffee from dripping on to
the base.
• If there is still water in the tank, place the pot under-
neath as soon as possible. Otherwise the filter might
overflow.
• Turn the device on.

NoTE:
• The control lamp in the switch lights up.
• The brewing process lasts approximately 13 minutes.
• When no more coffee is flowing through the filter you can
remove the pot.
• Turn the device off. The control lamp goes out.
• If you would like to pour the coffee out of the pot, press the
button on the lid.

NoTE:
The filter holder can be removed from the machine by its
handle. This makes it easier to dispose of the old coffee filter,
for example.
WARNING:
If you would like to make another pot of coffee immediately,
please turn the machine off. Allow it to cool down with the
water tank open in order to prevent hot water splashing out
when the machine is refilled.
05-KA 1360 CB.indd 21
Descaling
It is necessary to descale the coffee machine if the preparation
time becomes considerably longer.
• Only a commercially available decalcifier on a citric acid
base should be used for descaling.
• Please use the quantities stated on the pack or instruction
leaflet.
• After descaling, please boil fresh water without coffee in the
machine several times (approx. 3-4 times).
• This will remove any residues from the descaling process.
• Do not use this water for consumption.
Cleaning
WARNING:
• Before cleaning, always remove the mains plug and wait
until the device has cooled down.
• Do not immerse the device in water. Otherwise this might
result in an electric shock or
CAUTIoN:
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
• The exterior of the device should be cleaned as necessary
with a slightly damp cloth – without any additives.
• The filter holder can be washed as usual in warm washing
up water.
• Do not immerse the pot in water. Wipe the outside with a
moist cloth. You can clean the inside with warm water. If
necessary, use a soft brush.
Technical Data
Model: ........................................................................ KA 1360 CB
Power supply: .....................................................220-240 V, 50 Hz
Power consumption: ...................................................910-1100 W
Filling quantity: ..................................................................1,0 Litre
Protection class: ........................................................................... Ι
Net weight: ........................................................................1,85 kg
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
fire.
21
16.08.2010 16:24:29 Uhr