Preparation For Installation - Vistadoor M-E VDV-610 compact Mode D'emploi

VDV-600 | ENGLISH
INTRODUCTION
Thank you for choosing the VISTADOOR video intercom system. You
have purchased a high quality system with a stainless steel cover.
The elaborate stainless steel covers are made by hand and thus have
individual characteristics that should be considered a sign of quality.
Notes on caring for stainless steel
Please never clean the stainless steel surfaces with standard cleaning
materials, as these are too harsh. Please simply clean using spray desi-
gned for the cleaning and care of stainless steel. If this is not available
please use only clear water.
Brushed surfaces should always be cleaned with the grain and never in
a circular motion. This will avoid the creation of scratches.
Failure to observe these notes may lead to discolouration or even to
rust damage in extreme cases.
The system should be assembled by a specialist.
Key
1 Camera
2 Loudspeaker perforations
3 Bell button
4 Microphone
5 Casing screws
6 Lightness sensor
7 Volume potentiometer
8 Dip switch for the opening time of the door opener
9 Dip switch for the ID code
10 Connection terminal door opener
11 Connection terminal power supply
12 Connection terminal signal line
13 Connection terminal external camera

PREPARATION FOR INSTALLATION

The following lines are required:
Single-family house (VDV-610): 4 lines from the outdoor unit to the
indoor unit and 2 lines from the outdoor unit to the door opener.
Duplex house (VDV-620): 4 lines per bell push-button from the outside
unit to each apartment are required here, i.e. you need 8 lines from the
outside station to the inside (4 each per family 1 and 2) and 2 lines for
the door opener.
Up to four indoor units can be connected in parallel per residential unit.
The connection can either be laid from the indoor station or in a star
formation from a central point (distribution box).
The lines should be laid in such a way that they are fed out of the wall
directly behind the relevant outdoor/indoor unit.
Note: It is also possible to combine video and audio compon-
ents with the VISTADOOR system.
INSTALLATION OF THE OUTDOOR STATION
Preparation
When removing the front cover please ensure that the nameplates do
not fall out as this could damage them.
The camera should be installed at a height of approx. 1.4m-1.6m
(camera centre) (figure 3).
1. Remove the two bottom screws (5) using a suitable screwdriver.
2. Using the thumb and index finger, hold the front cover and pull it
forward slightly. Then gently lift and remove it. Take care not to
tear off the microphone cable. A plug connects microphone cable
and electronics – remove by simply unplugging.
3. Remove the terminal cover by unscrewing the two screws and then
removing the plastic cover.
4. Look for a suitable place to install the outdoor unit and lay the
necessary lines to this point (figure 3).
Note: Ensure that the wall at the installation location is
straight and level.
5. Drill four holes into the wall using the drilling template (Ø 6 mm).
Place the drill template at the outdoor unit installation position
on the wall and use a water level to ensure it is straight. Stick the
drilling template on with sticky tape and then drill the four holes.
6. Remove the drill template and place one of the included dowels in
each drill hole.
7. Feed the line through the designated opening on the reverse of
the outdoor unit.
8. Now screw the outdoor station closed with the 4 fixing screws.
Make sure that the housing does not become distorted when
tightening.
Adjusting the nameplate
The nameplate comprises two transparent plastic parts that are
connected with 2 small screws.
9. Remove both screws and take the nameplate apart. The foil for
inscription is between the two plastic parts.
10. Write on the foil with a smear-resistant felt pen or print a name-
plate with the dimensions 71 x 15 mm using a PC and printer.
11. Place the inscribed nameplate (foil) between the two plastic parts
and screw them back together.
12. Lay the nameplates into the outdoor station and fix them with a
strip of adhesive tape.
13. Plug the microphone cable into the socket again and fit the front
cover onto the outside station - from the top and at an angle. Take
care not to pinch the microphone cable. The back cover catches
must hook into the front cover recesses.
14. Thereafter, carefully slide the front cover over the outside station
and screw the two fastening screws (5) back into the enclosure.
CONNECTION
Connect the laid line to Audio 1, +15V, GND and Video 1 (figure 2) on
the outdoor station and connect it with the indoor station/s. These are
also present on the indoor station and need only be connected with one
another 1:1.
6