Vistadoor M-E VDV-610 compact Mode D'emploi page 23

release button. A double beep on the external and indoor unit confirms
the door has been released and the green name plate also lights up
green if the door release mechanism is activated.
The door release mechanism can be activated if:
1. somebody rings the doorbell (within 60 seconds and without having
to establish voice communication first);
2. the reply function is on.
Set the doorbell chime
1. Press the speak button (monitor switches on).
2. Press the chime button to play the chime set.
3. Press the chime button to play the next chime and repeat this
process until you find the chime you want.
4. Press the speak button to save the chime (monitor switches off).
There are 12 different chimes to choose from.
Set the handset volume
Use the handset volume control on the side of the indoor unit to
infinitely adjust the handset volume of the person at the other end.
Set the doorbell volume
The volume can be infinitely set between 0% and 100% using the
doorbell volume control on the mainboard (adjust the volume with
a small screw driver; turning clockwise to increase the volume and
anticlockwise to decrease it).
Be careful not to overtighten the potentiometer.
Disable the doorbell chime (e.g. at night)
The doorbell chime can be disabled. To do this, press the sleep button
on the indoor unit once. The LED below the sleep button flashes red to
show that the chime has been disabled. To activate the chime again,
press the sleep button again; the LED will stop flashing and the chime
will be reactivated.
The optical signal (light surrounding the speak and door release
buttons) remains activated even if the doorbell chime is disabled and
continues to indicate that the doorbell has been pressed.
NOTE: If the VTX-BELL module is used, this will also be
disabled during sleep mode, i.e. the signal from connected
receivers is also disabled.
Activate alarm
The external station can sound an alarm (e.g. if you are being
harassed). To do this, you have to press and hold the alarm button on
the indoor unit. The alarm only sounds if the button is pressed and
held down within 60 seconds after the doorbell was pressed or if voice
communication is established.
Intercom
If several indoor units are connected in parallel, you can communicate
between these indoor units.
If you press the alarm button when the station is on standby, all indoor
units connected in parallel will sound the alarm. Voice communication
is established if the handset is lifted on one of the ringing indoor units
or the speak button is pressed. To end the call, either put the handset
down or press the speak button.
Activate the monitor / switch through additional cameras
The monitor button allows you to monitor the entrance area at any time
without somebody having to press the doorbell. Pressing the monitor
button a second time turns it off.
NOTE : If an additional camera (model: VD 500 XCam) or several
external stations are connected, these can be activated using the
monitor button. Pressing the monitor once activates the external station
camera, pressing it a second time turns on the first additional camera
and pressing it a third time turns on the second additional camera. If
all the cameras are switched through, you can see the image from the
first camera. You can only disable the monitor by double pressing the
speak button or wait approx. 60 seconds until the system automatically
returns to standby mode.
Adjust monitor brightness
You can use the brightness button to adjust the monitor brightness to
seven levels. Each time you press the brightness button, the brightness
level increases; the brightness returns to the lowest level when it
reaches level seven.
Adjust the monitor contrast
You can use the contrast button to adjust the monitor contrast to seven
levels. Each time you press the contrast button, the level increases; the
contrast returns to the lowest level when it reaches level seven.
Adjust the colour saturation of the monitor
You can use the colour saturation button to adjust the monitor colour
space to seven levels. Each time you press the colour saturation button,
the level increases; the colour space returns to the lowest level when it
reaches level seven.
TECHNICAL DATA
Operating voltage: 15 V DC
Current consumption: 220 ± 50 mA
Temperature range: -10°C to +50°C
Maximum humidity: 85%
INFORMATION
Information regarding CE - Conformity
The functionality of the unit can be affected by the influence of strong
static, electrical or high frequency fields (discharging, mobile phones,
radios, microwaves).
Cleaning and maintenance
Always disconnect mains powered units from the mains supply before
cleaning (disconnect the plug). The unit housing can be cleaned using
a soapy soft cloth. Do not use any abrasive materials or chemicals.
Remove dust build-up from ventilation slits using a brush and clean up
using a vacuum cleaner. Do not hold the vacuum cleaner nozzle directly
against the unit.
Safety instruction
In the event of damage to the housing, connectors, power cables or
isolation shielding, switch off the device immediately and disconnect
ELECTRIC SHOCK – DANGER OF LOSS
from the mains power.
OF LIFE . (Unplug the mains connector from the socket!). Damage
should be repaired immediately by a specialist!
Never carry out repairs yourself!
7
ENGLISH | VDV-505