Intercom With Channels "A" And "B; Important - SCHUBERTH SRC SYSTEM PRO Mode D'emploi

6.1b PAIRING WITH A "1+8" INTERCOM BUDDY
1. In Standby, press for 5 seconds to enter pairing mode.
s
2. Enter "1+8" intercom pairing mode on the second unit. After a few seconds the
units should recognize each other.
3. If pairing was successful, a purple light appears for 2 seconds.
If your SRC-System™ PRO already has a full list of 8 paired "1+8" Intercom Buddies,
pairing another buddy will replace the buddy that you have not spoken to for the longest
time.
Pairing Online – Cardo Community®
You can also find your friends and add them to your "1+8" Buddy list via the
Cardo Community (see section 3).
6.1c PAIRED DEVICE INDICATION
You can see which units within a range of 20m are your "1+8" Intercom Buddies.
s v
In Standby, press and for 2 seconds
Paired Device
If "1+8" Buddies are within range, the LEDs on both units will
Indication
turn PURPLE for 2 seconds
6.1d CALLING "1+8" INTERCOM BUDDIES
There are two ways to start an intercom call with "1+8" buddies.
OPTION 1: Voice Connect (VOX)
Speak any word loudly into the microphone. When you hear the Voice Command
tone, say the name of a "1+8" Intercom Buddy i.e. "John Smith"
|
SRCS Pro
32
☛
OPTION 2: MANUAL MODE
CHOOSE THE NAME
SAY THE NAME
(from your Buddy List):
s
Press for 2 seconds. Hear the names of all pre-
paired "1+8" buddies.
s
Tap and say
When you hear the name of the Buddy you wish to call,
the name of the
s
tap or say any word loudly into the microphone.
"1+8" Buddy
To cancel Buddy List playback: Press s for 2 seconds.
INTERCOM-TO-PHONE
If a "1+8" Buddy is not in range, or moves out of range, you have the option to
set up the "Intercom-to-Phone" feature via the Cardo Community, to remain in
contact by diverting Intercom calls automatically to your mobile phones.

6.2 INTERCOM WITH CHANNELS "A" AND "B"

Start multi-party conversations using Intercom Channels "A" and "B". This mode
is suitable for 2, 3 or 4-way calls.
6.2a PAIRING INTERCOM CHANNELS "A" AND "B"
Pairing a Channel will replace any existing paired device on that Channel with the
newly paired device.
1. Check that all units are in Standby.
2. Press v for 5 seconds until the LED begins flashing rapidly, indicating it is in
Intercom Pairing mode (see table below for channel pairing).
CHANNEL PAIRING METHOD LED INDICATORS
In Standby, press v for 5 seconds. Channel
"A" Rapid RED flashing
"A" pairs automatically.
In Standby, press v for 5 seconds.
"B" Rapid BLUE flashing
When LED begins flashing , tap v twice.
3. Enter Intercom Pairing mode on the second unit following its user manual.
Both units will now be in Intercom Pairing mode.
4. After a few seconds, both units will show a solid LED for 2 seconds, indicating that
they are paired and ready to use.
5. If Pairing is not completed within two minutes, the units will return to Standby
mode.
6.2b CALLING INTERCOM CHANNELS "A" AND "B"
There are two ways to start an intercom call with Channels "A" and "B"
OPTION 1: Voice Connect (VOX)
Speak any word loudly into the microphone. When you hear the Voice Command
tone, say "Call Intercom" to start an intercom call with "A" and/or "B" (subject to
who is present)
VOX Intercom call with only "A" or "B" will end automatically after 30 seconds of
silence.
☛
OPTION 2: Manual Mode
Use this to start an Intercom call with either:
• Channel "A": Tap v
• Channel "B": Double-tap v
To end a call tap v .
If you are already in an Intercom call with "A" or "B", tap v twice to add a third
rider ("A" or "B").
THREE-WAY INTERCOM
Rider 2
Rider 3
Rider 1
Pairing
Rider "1" is paired to Rider "2" and also to Rider "3".
1. Rider 1 pairs to Rider 2 using Channel "A" (see 6.2a).
2. Rider 1 pairs to Rider 3 using Channel "B" (see 6.2a).
IMPORTANT: Three-Way Conference Mode Considerations
During a 3-Way Intercom Conference call with 2 other participants, Rider 1 will not be
able to receive mobile phone calls or GPS navigation instructions as long as the call is in
progress.
SRCS Pro
|
33