Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Jandy
TruClear
Chlorine Generating System
®
™
Section 5. Operating Instructions
5.1
Turning Power Pack On/Off (Manually)
To turn the Jandy chlorine generating device on or off
To turn the Jandy chlorine generating device on or off
press the
button.
A quick press will place the chlorinator into "standby"
state. While in "standby" mode a quick press will return
to "chlorinating" mode. If held down for 6 seconds it
will completely power down.
NOTE
Because the power pack is wired to the pump's power
source, the power pack can only be turned on when the
pump is turned on.
In normal operation, the up and down arrows are used to set the output level of the chlorinator.
The output should be adjusted in order to achieve the desired Free Available Chlorine level of 2-4 ppm.
The back/save button will save any changes you have made in the menu and send you back to the previous
menu screen. The select button will scroll through and open any available parameters for editing.
*When connected to an automation system via RS485, full control of the TruClear system is given
over to the automation controller. No functionality will persist at the TruClear UI. In order to control
the TruClear from the UI, the automation system must fi rst be placed into service mode. For details
on service mode please consult the operation manual for the controller you are using as follows:
● AquaLink
RS: 6594 ● Z4: H0386500 ● PDA: H0572300
®
|
Installation & Operation Manual
5.2
Press and hold the
simultaneously for fi ve seconds
to access the service menu. Use
the
exit when your selection has been made.
5.3
If the power pack is wired to the pump's external timer
and the power to the unit is on, the power pack will
automatically turn on and off when the pump turns on
and off (see Section 3.5). When the power pack is wired
as such, the only setting that must be set manually is the
∞ DISPLAY
Shows TruClear™ status and chlorine
production percentage.
Indicates TruClear is in standby mode
and will not be producing chlorine even
if the filter pump is running.
Indicates TruClear has detected filter
pump activation and is initiating chlorine
production.
Indicates TruClear is currently producing
chlorine and displays current production
output percentage.
Indicates TruClear is connected to a
remote automation system via RS485*.
Press to turn power to system on. Press and hold
for 6 seconds to completely power the system
down. A single quick press will toggle the system
from Standby to Auto mode when not connected
to a remote automation system via RS485*.
appropriate levels to protect the chlorine from the UV
rays of the sun.
NOTE
ENGLISH
Select Language
buttons
button to select language. Press the
Turning Power Pack On/Off (Using the
Pump's External Timer)
chlorine output level (see Section 5.4).
5.4 Chlorine Output Level
When setting the chlorine output level, the
factors to consider are:
- number of gallons in the pool
- number of bathers (bather load)
- amount of pollen and dust going in the water
- number of hours the pump runs
- whether you are using a single or variable
speed pump
- climate and water temperature
- amount of rain water entering the pool.
A good starting point for pools at 15K gallons
and under should be 40%. Pools closer to
the 25K to 30K gallons should use 60% as a
starting point.
If you fi nd that these levels do not provide
the 1 - 3 PPM chlorine residual that is
desired, then raise the output level higher to
compensate.
If you fi nd that output level is approaching
90% to 100% and testing the pool water
shows no or very low chlorine residual, your
pool may need to be manually shocked due
to a waste load that has built up in the pool
water that is overwhelming the chlorine you
are supplying to the pool. Another cause
may be the lack of Cyanuric Acid (CYA) at
The unit only runs while your pump is running. More
pump runtime will result with more chlorine in the water.
Page 21
button to
Publicité
Chapitres
Table des Matières
Dépannage
