EGO POWER+ SNT2400E Manuel De L'opérateur page 7

1. Loosen the knob on the inner support pole and
remove the bolt (Fig. D1). Save the knob and bolt for
reassembly.
D-1 Snow-Discharge Chute
D-3 knob
D-5 Base
2. Lift the snow-discharge chute assembly, align the
outer support pole with the inner support pole to slide
the outer support pole into place. Make sure that the
snow discharge chute is seated on the base (Fig. D2).
3. Secure the snow discharge chute assembly with the
reserved knob and bolt.
OPERATION
TO ATTACH/DETACH THE BATTERY PACK
CHARGE BEFORE FIRST USE.
Use only with battery packs and chargers listed in fig. A4
NOTE: For best performance, we recommend use with
two 5.0 Ah EGO 56V Arc-Lithium batteries or with two
EGO 56V Arc-Lithium batteries of greater capacity.
When not in use, 56V battery packs should be stored
in an enclosed area where the temperature will not
drop below -20°C. Optimal charging temperatures are
between 5°C and 40°C.
To Attach
Push the battery pack into the battery compartment
until you hear a "click" (Fig. E1).
To Detach
Depress the battery-release button in the battery
compartment (Fig. E2).
NOTICE:
Make sure that the latch on the snow blower
snaps into place and that the battery pack(s) are secured
to the unit before starting operation.
STARTING/STOPPING THE SNOW BLOWER
CAUTION: Do not attempt to override the operation
of the safety button.
WARNING: Ensure that other people and pets remain
at least 30m away from the snow blower when it is in use.
WARNING: The auger will continue to rotate for a
few seconds after the snow blower is turned off. Allow
the auger to stop rotating before starting it again.
NOTICE: Do not rapidly turn the snow blower off and on.
To Start the Snow Blower
D-2 Outer Support Pole
1. Ensure that the handle assembly is securely adjusted
D-4 Inner Support Pole
D-6 Bolt
2. Insert the battery pack(s) to the snow blower and close
3. Press the safety button (A-16) and hold for 1 second,
NOTICE: The snow blower can be turned on by the
auger switch trigger only when the LED indicator blinks.
NOTICE: The snow blower may not properly start if its
batteries' temperature is -20°C or less. If the snow
blower doesn't start, remove the battery from the snow
blower and allow it to warm indoors for 10 minutes or
longer. Reinstall the battery and try again.
To Stop the Snow Blower
Fully release the auger switch trigger.
NOTE: The electric brake in the Automatic Braking
Mechanism will stop the auger rotation within 3
seconds of the auger switch release.
Variable-Auger-Speed System
The speed of the auger can be adjusted to control the
throwing distance.
To increase/decrease the speed, push the auger speed-
control lever (A-15) forwards/backwards.
Variable-Speed Self-Propel System
This snow blower is equipped with variable-speed self-
propel capability. it is independent of auger rotation.
To operate the self-propel system without auger rotation,
press the self-propel trigger (A-18) to the handle. To
increase the speed, move the self-propel-speed control
lever (A-17) forwards. To decrease the speed, move the
self-propel speed control lever backwards.
To turn the self-propel function off, release the self-
propel trigger.
To move the snow blower backward, first stop the self-
propel function; pull the self-propel speed-control lever
to REVERSE Position, then press the self-propel trigger.
56-VOLT LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400E
to appropriate height, the side-discharge chute
assembly is mounted properly, the chute and chute
deflector are adjusted to an appropriate position.
the battery cover.
and the LED indicator (A-21) will blink green. Press
the auger-switch trigger (A-13) to turn on the snow
blower while the LED indicator blinks.
EN
7