Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
The wires are coloured according to the following
code:
live = brown
neutral = blue
• Do not connect the blue or brown wire to the
earth terminal in the plug.
Connect as follows:
- brown to terminal marked 'L'
- blue to terminal marked 'N'
The plug fitted should comply with BS EN 60309
(BS4343), 32 Amps.
Always ensure that the cable clamp is
correctly and securely fitted to the
sheath of the cable.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor size
2
is 1.5 mm
. When using a cable reel, always unwind
the cable completely. Also refer to the table below.
Conductor size (mm
2
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
20
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
Assembly and adjustment
Bench mounting (fig. A)
Mounting holes (8) have been provided to facilitate
bench mounting.
Removing and fitting a cutting blade (fig. B & C)
• With the arm in the rest position, use the lip (11)
to slide the guard (4) back. Leave the guard
retracted (fig. B).
• Press and hold down the spindle lock (5) (fig. C).
• Rotate the cutting blade until it locks.
• Rotate the bolt cover (12) out of the way (fig. B).
• Using the Allen key (10), remove the bolt (13) by
turning counterclockwise and then remove the
lock washer (14), the flat washer (15) and the
retaining flange (16) (fig. C).
• Replace the cutting blade (17). Make sure that
the new blade is placed correctly onto the flange
(18).
• Secure the blade with the retaining flange (16),
the flat washer (15) and lock washer (14) and the
bolt (13).
• Move the guard back down and release the
spindle lock (5).
Clamping the workpiece in position
60
(fig. D, E, F, G, L, M & N)
Your D
WALT toothed chopsaw is equipped with a
E
6
10
material clamp (6).
15
• Pull the lever (19) toward the handle (20) (fig. D).
20
• Push the clamp shaft (21) forward until the jaw
25
(22) is almost touching the workpiece.
-
• Press the lever (19) toward the jaw (22) until it
-
-
engages with the clamp shaft (21).
6
6
• Rotate the handle (20) clockwise and clamp the
6
6
workpiece securely.
15
• To release the workpiece, rotate the handle (20)
15
counterclockwise.
20
-
• Support long workpieces using a piece
Prior to assembly and adjustment always
unplug the tool.
The teeth of a new blade are very sharp
and can be dangerous.
of wood (23) (fig. E). Do not clamp the
cut off end (24).
E N G L I S H
en - 5
Publicité
Table des Matières
