Jiffy Pro II LECTRIC Mode D'emploi page 4

BATTERY OPERATING INSTRUCTIONS
LED OUTPUT
STATUS VOLTAGE
Off No Output
Off No Output
Off No Output
Red Vbatt 3-7Volts
(blinking) typ.
Red Vbatt 7-13Volts
typ.
Yellow Vbatt 13.0 -
13.5Volts
Green Vbatt 13.5Volts
Green Vbatt >
(blinking) 13.5Volts
*NOTES:
1. Vbatt is the battery voltage
2. Battery overly discharged; may not fully charge.
3. LED may blink momentarily if the above connection procedure is not
followed.
Always keep your internal AGM battery fully charged.
Plug your Battery Doc® Charger/Maintainer into any 110
volt outlet after each
Charger/Maintainer will not over charge the battery.
External Battery Information (optional)
The JIFFY STX PROII LECTRIC requires a 12 volt, deep cycle, lead
acid battery. Jiffy recommends an AGM battery.
The power source should be chosen carefully. The battery directly
affects the performance of the drill. A battery that is too small or in
poor condition will reduce power and cycle time.
The battery should be fully charged before every use.
ensure maximum performance from both your JIFFY LECTRIC power
ice drill and the battery.
Use the included Jiffy part #3917, 8 ft Connection Cable to connect to
an external battery.
Replacement Blade
Improper cutting may be due to dull or damaged drill teeth or drill point.
Maintain sharp blade teeth and point. Preserve the original factory
cutting angles when sharpening your drill. File blade teeth and use a
disk sander to sharpen the point. For professional service see your
Jiffy service center. Only genuine Jiffy blade teeth are to be used.
Blade Replacement Instructions
When replacing blade teeth, the beveled edge of teeth and the head of
the capscrews should face the ice. The stamped part number on the
teeth should face away from the ice, as shown in the diagram. Use
two 7/16" wrenches to remove the capscrews and to retighten after
replacement. CAUTION – THE BLADE TEETH ARE SHARP AND
SHOULD BE HANDLED CAREFULLY TO AVOID FLESH CUTS OR
INJURY.
CONDITION *NOTES
Charger not plugged
in
Output Shorted
Battery Voltage 2
below 3Volts
Charging 1 & 2
Charging full Amps
(1 or 2A)
Charging < 70% full
Amps
Battery fully charged
(OR not connected)
Check for incorrect 3
battery
use. Battery Doc®
This will
JIFFY® PROII LECTRIC™ ICE DRILL –
Ref. Part
No. No.
1 4155
2 1719
3 4289
4 3810
5 3918
6 4261
7 4265
8 2512
9 3961
10 3968
11 4270
12 4150
13 4152
14 4266
15 2451
16 4151
17 4156
18 3946
19 4153
20 3921
21 1683
22 1689
23 1119
24 4154
25 4267
26 3965
27 2355
28 3922
29 4269
30 2336
31 3351
-4-
PARTS LIST
Description
Cover
Locknut
Machine Screw
Motor
Wire Assembly
Battery
Wire Assembly
Push Nut
Switch
"U" Handle
Throttle Clip
Throttle Assembly
Switch Mounting Bracket 1
Wire Assembly
Locknut
Battery Holder
Hex Capscrew
Handle Plate
Battery Clamp
Motor Mounting Plate
Hex Capscrew
Flat Washer
Lock Washer
Plug Bracket
Cable Asbly w/ Connector 1
"L" Handle
Hex Capscrew
Locknut
Machine Screw
Locknut
Hex Capscrew
No.
Used
1
2
2
1
1
1
1
2
1
1
1
1
1
2
1
2
1
1
1
1
8
1
1
1
4
6
2
2
2