Stid SPECTRE Notice D'installation page 4

SPECTRE Access UHF
Read only & OSDP™
Installation procedure
The number of antennas, the number of channels and the communication protocol are configurable with the Ultrys V2 application or when the module is ordered.
TTL protocols (Wiegand & ISO2):
▪
- ISO2 (Clock & Data) - Decimal (7 bytes max)
- Wiegand 26-bit
- Wiegand with LRC - Hexadecimal (12 bytes max) + LRC
- Wiegand without LRC - Hexadecimal (12 bytes max).
Serial protocols (RS232 & RS485): The structure of the frame can be configured with the following optional parameters (in gray):
▪
1 byte
STX
Channel number + Tag Data*
0x02
- STX+ETX: add 0x02 (STX) and 0x03 (ETX) at the start /end of frame - CR/LF: Carriage Return (0x0D + 0x0A) configurable separately
- LRC: Checksum (XOR of all previously bytes except STX) - Data sent in: decimal or hexadecimal
- ASCII: if this option is activated, the data will be sent in ASCII mode (data size will be doubled) - Non-significant zero: complete the tag data with not
significant 0 to obtain the defined data size - (Channel no. + 0 padding + tag data, etc.).
OSDP™ protocol (RS485: 7OS): refer to Spec_Protocole_7OS_OSDP_UHF-US.pdf.
▪
When the reader is switched on: the reader's red LED lights up. Reader initializing.
After initializing, the reader will look for a configuration tag for about 15 s, on antenna 1 (connected to RF port 1).
• If no tag detected: the antenna LED flashes "color RFON" (200ms) (blue by default) / RFOFF (200ms).
• If any tag detected: the antenna LED displays the sequence "color RFON" (blue by default) / "color DETECTION" (orange by default) for 200ms then LED OFF.
• If a configuration tag is detected: the antenna LED displays the sequence « color RFON "(blue by default) / "color DETECTION" (orange by default) for 200ms then
LED OFF then the antenna LED gives the followings indications:
• 3 GREEN flashes (500ms ON; 200ms OFF): the configuration tag is taken into account.
• 3 RED flashes (500ms ON; 200ms OFF): the regulation (region) of the configuration tag does not match to the regulation of the reader.
• 3 PURPLE flashes (500ms ON; 200ms OFF): the key of the configuration tag does match to the reader key.
• 5 RED flashes (500ms ON; 200ms OFF): the model of the reader of the configuration tag does match to the model of the reader.
The end of the start sequence is indicated by the flashing of the reader LEDs (red and green) 3 times (500ms ON; 500ms OFF).
Power supply OK:
Power supply too low:
Temperature error:
RF error, antenna problem:
Communication:
© STid - 20 PA des Pradeaux FR13850 Gréasque - NI1127X07 - Page 3 sur 18 - Ed. 28/05/2021
UHF SPECTRE Access
Lecture seule & OSDP™
Notice d'installation
1 byte + X bytes
0x0y nn.....nn
fixed red LED
blinking red LED (500ms ON / 500 ms OFF)
blinking red LED 5 times after all reading sequence. (RF Scan)
blinking red LED 3 times after all reading sequence. (RF Scan)
Green LED
Configuration - SMA / SLA
1 byte 1 byte 1 byte
LRC CR LF
0x0D 0x0A
Start Sequence - SMA / SLA
LED indication - SMA / SLA
Dimensions (mm/in) - SMA
UHF SPECTRE Access
Solo lectura & OSDP™
Manual de instalación
1 byte
ETX
0x03
US
FR
ES