Husqvarna DE 110S Manuel D'utilisation page 17

b) Push "II" for automatic start. Refer to
start function (Only 230V DE 110S and DE 110)
on page 16 .
5. To stop the product, set the On/Off switch to "0".
6. Disconnect the product from the power socket.
To start and stop DE 110/DE 120
Note:
Wait for 5 seconds after you start the product
to operate with full suction. The suction is not at full
capacity directly at start.
1. Make sure that the frequency and voltage shown on
the rating plate agree with the power supply.
2. Connect the product to an applicable power socket.
3. Push the "I" on the main switch to start the product.
(Fig. 17)
4. Push the On/Off button to start and stop the
operation. (Fig. 18)
a) Push "I" to start the operation.
b) Push "A" for automatic operation start. Refer to
Automatic start function (Only 230V DE 110S
and DE 110) on page 16 .
5. To stop the operation, push the On/Off button. The
button goes off when you stop the operation.
6. Push the "0" on the main switch to stop the product.
7. Disconnect the product from the power socket.
Hour meter (DE 110/DE120)
The hour meter shows the total operation time of the
product in hours.
To remove dust particles from the
prefilter during operation
The filter purge procedure cleans the prefilter from
unwanted material. Do the procedure in these situations:
• Before a work stop or at the end of each work day.
If the product is off for a while, it gives the dust
more time to fall down. This makes the filter purge
procedure more powerful.
• When the suction is not sufficient.
• Before installation of a new Longopac bag.
• When the prefilter clogged alarm goes off. Refer to
the instructions on the decal on the prefilter cover.
1. Start the product. Refer to
110S on page 16 or To start and stop DE 110/DE
120 on page 17 .
2. Close the air flow that moves through the air intake
with the air intake plug or the intake valve to make
vacuum. (Fig. 19)
3. Wait 5 seconds until vacuum is made, then push the
filter purge button. Do this step 3 to 5 times. It is
important to let the product make vacuum between
each button push. (Fig. 20)
1587 - 007 - 24.01.2022
Automatic
To start and stop DE
If the suction is not sufficient after this procedure, it is
necessary to clean the prefilter with water. Refer to
clean the prefilter with water on page 20 .
To install a new Longopac bag cassette
CAUTION:
you install a new Longopac cassette. Refer
To remove dust particles from the prefilter
to
during operation on page 17 .
1. Put the Longopac cassette around the inner edge of
the Longopac holder.
2. Remove the 4 straps after you put the Longopac in
the holder.
3. Pull the inner layer of the Longopac cassette up (A)
and fold it into the holder (B). (Fig. 21)
4. Attach the Longopac holder to the rear part of the
container (A). Then attach the Longopac holder to
the sides and to the front of the container (B). Push
the Longopac holder up until you hear a solid click.
(Fig. 22)
5. Make sure that the Longopac is sealed. (Fig. 23)
6. Pull the outer layer of the Longopac cassette down.
(Fig. 24)
7. Close the bottom of the Longopac with a cable tie.
(Fig. 25)
To discard a full Longopac bag and
prepare a new Longopac bag
WARNING:
Longopac bag with caution, a full Longopac
bag can be heavy. Make sure that the cable
ties are closed correctly before you lift the
Longopac bag.
1. Pull out the Longopac bag (A) and attach a cable tie
(B) to close the new Longopac bag. (Fig. 26)
2. Shake down the dust in the used Longopac bag.
3. Attach a cable tie 10 cm/3.9 in. below the first cable
tie to close the used Longopac bag. Cut off the
Longopac bag between the cable ties. (Fig. 27)
4. If the remaining part of the Longopac bag cassette
is too small to prepare a new Longopac bag, install
a new Longopac bag cassette. Refer to
new Longopac bag cassette on page 17 .
5. Obey local regulations for disposal of the full
Longopac bag.
To do after completed work
1. Do the filter purge procedure. Refer to
dust particles from the prefilter during operation on
page 17 .
To
Clean the prefilter before
Lift the
To install a
To remove
17