Cleaning And Maintenance - Asist AE6PV030 Mode D'emploi

Place the product in the safety holder. Plug the power
cord into an electrical outlet. Let the stylus heat up for
about 2-4 minutes.
Shutdown
If the product cools down, do not leave it unattended.
There is a risk of fire.
After use, place the stylus on the safety holder. Un-
plug the power cord from the AC outlet.
Allow the product to cool completely before storing.
Operation
When working with new material, always test the
workflow on a piece of sample.
The longer the burn stamp is applied, the darker the
resulting motif will be.
You will need solder and flux for soldering. Many sol-
ders already contain flux. To clean the soldering iron
You will still need a soft sponge to clean the soldering
tips. There are no soldering accessories
part of delivery.
Pyrography
Choose one of the firing tips as the tool.
If necessary, clean the object you are working on.
Sand the surface with sandpaper.
Switch on the device. Hold the device only by the
handle and do not touch metal parts.
Hold the product in the same way as you hold a
fountain pen. Guide the firing tip over the material
under gentle pressure. You can create decorations,
for example, on wood, cork or leather.
Burning stamps
Choose one of the firing patterns as a tool.
Hold the tool by the handle, perpendicular to the wor-
kpiece. Apply the pattern to the object under gentle
pressure. You can use this type of decoration, for
example, on wood, cork, leather or sealing wax.
Burning blade
Choose the blade and blade holder as the tool.
Insert the blade into one of the holes in the holder.
Screw the blade holder onto the device.
Hold the appliance only by the handle and do not
touch metal parts. In this way you can cut polystyre-
ne, for example.
Soldering iron
Screw the soldering tip onto the device.
Remove grease, dirt, oxides and sulphides from the
soldered parts.
Hold the device only by the handle and do not touch
metal parts. Using a soldering tip, apply a little solder
to the soldered part and join them together.
Use flux if necessary.
Make sure that the soldering tip of the soldered joints
touches only slightly. Clean the soldering tip with a
cleaning sponge.

CLEANING AND MAINTENANCE

Unplug the power cord from the AC outlet before
beginning any installation, adjustment, repair, or
maintenance activity. Regularly remove dust and dirt
from the machine with a brush or damp cloth.
The pen requires no maintenance other than occasio-
nal cleaning.
Before cleaning, unplug the power cord from the
electrical outlet and leave the soldering iron
cool completely.
Use a soft, lint-free, antistatic cloth for cleaning.
Do not use any chemical or abrasive cleaners.
When cleaning the handpieces, screw them onto the
instrument and turn on the instrument. Clean the hot
handpiece with a damp one
non-flammable sponge.Attention. danger of burns.
Do not clean the handpiece with a metal brush or
sandpaper.
SPECIFICATIONS
Power supply: 230V ~ 50Hz
Power consumption: 30W
Tip temperature: 450 ° C
Plastic case with set of 23 pcs:
10x firing tip
9x firing dies
1x soldering tip
1x blade
1x blade holder
1x safety stand
cable length: 1.2m
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
35