Additional Safety Instructions; Use And Operation - Asist AE9BS06DN Mode D'emploi

ADDITIONAL SAFETY INSTRUCTIONS

Please read these safety instructions before use and
keep them in a safe place.
! - This symbol indicates the risk of injury or damage
to the device.
• The multifunction sharpener can run continuously for
a maximum of 10 minutes and then must cool down
for at least half an hour.
• The multifunction sharpener is suitable for dry focu-
sing and must never come into contact with liquids.
• The multifunction sharpener can only be used to
sharpen HSS (high speed steel) drills, knives and
shears with straight edges, straight and chisel blades.
• Sparks are generated when focusing. Keep the
washer at a safe distance from flammable liquids and
materials.
• Be careful not to touch the grindstone and proce-
ssed material immediately after use, as they are very
hot.
• If the processed material turns blue during the
sharpening process, it is overheated and may be
damaged. When sharpening, cool the regularly proce-
ssed material, eg with water.
• The multifunction washer can be used only when the
adapter is installed.
• The adapter must not be removed or mounted when
turning the grindstone.
- Use protective equipment against noise, dust and
vibration !!!
SAVE THESE SAFETY INSTRUCTIONS !!!
DESCRIPTION (A)
The universal grinding station is designed for shar-
pening and grinding tools (drills, scissors, knives, flat
chisels, chisels, etc.).
The machine may only be used for its intended pur-
pose. Any other such overuse does not correspond to
the intended use. The resulting damage or injury of all
kinds is the responsibility of the user / operator and
not the manufacturer.
Please note that our devices have not been designed
for commercial, craft or industrial use, depending on
their intended purpose. We do not accept any liability
if the device is used in trade, craft or industrial enter-
prises and in comparable activities.
1 Mains plug
2 Attachment for sharpening knives and scissors
3 On / Off switch
4 Spacer
5 Support plate
6 Attachment for sharpening chisels and planing
knives
7 Adjusting the angle
8 Protective cover
9 Workbench mounting holes
10 Grinding wheel
11 Drill sharpening attachment
12 Nuts for fixing the drill
13 Lever
14 Drill holder
15 Adjusting tray
16 Grinding wheel nut
Pictograms
Pictograms on the product packaging:
a) Power supply values
b) Power consumption
c) Idle speed

USE AND OPERATION

ASIST tools are intended for home or hobby use only.
The manufacturer and importer do not recommend
using this tool in extreme conditions and under high
loads.
Any additional requirements must be the subject of
an agreement between the manufacturer and the
customer.
Always make sure that the tool is switched off and
unplugged before starting work or making any ad-
justments to the appliance.
The delivery includes three sharpening / grinding
attachments:
Attachment for sharpening knives and scissors
Attachment for sharpening chisels and planing knives
Drill sharpening attachment
The attachments serve as guides and enable precise
and safe grinding and sharpening of tools.
Never use the sanding station without the attachment
attached for sharpening.
Always wait for the grinding wheel to stop before
removing the sharpening attachment.
STORAGE OF ATTACHMENTS
On the sides of the sanding station, there are guide
rails that are used to store sharpening attachments
when not in use.
Insert the unnecessary extensions from above into
the guide rails on the sides of the station.
CONSTRUCTION
Place the machine on the work surface so that the
grinding wheel points towards you. Attach the machi-
ne to the work surface using the workbench mounting
holes and screws (not included).
ASSEMBLY OF FOCUS ATTACHMENTS
Before mounting the attachments, make sure that the
device is switched off.
1) Slide the required sharpening attachment from
above into the guide rails over the grinding wheel.
2) Slide the attachment downwards until you hear it
37