Additional Safety Instructions; Use And Operation - Asist AE6PV030 Mode D'emploi

ADDITIONAL SAFETY INSTRUCTIONS

Please read these safety instructions before use and
keep them in a safe place.
! - This symbol indicates the risk of injury or damage
to the device.
ATTENTION! When not in use, this tool must be
placed on a stand.
Do not use the product on humans or animals. The
product is not intended for use in persons (including
children) with reduced physical ability, in persons
whose perception or mental abilities are impaired, or
in persons whose experience or knowledge is lacking.
Children must not play with the appliance.
Do not apply excessive pressure to the tips during
use. Thin tips can bend under pressure.
• If the device is handled carefully, a fire may result.
• Make sure that the connecting cable does not come
into contact with heat, oil or sharp edges. Damaged
connecting cables can cause fire, short circuits and
electric shocks.
• Remove flammable objects, liquids and gases from
the work area of the device before use. Keep your
work area clean to prevent accidents. • Before use,
make sure that the tool tip is properly connected to
the device. The hot tip of the tool and its container
must not come into contact with the skin, hair, etc.
When not in use, store the appliance in a safe place
protected from dust and moisture.
• Check that the appliance is not damaged. Do not
use if damaged!
• Ensure adequate ventilation during use. Ensure
that toxic gases or vapors cannot be inhaled. Wear
protective clothing.
• Disconnect the appliance from the power supply for
longer work interruptions.
• Observe national and international regulations on
safety, health and health at work.
Do not expose the product to extreme temperatures,
direct sunlight, strong shocks, excessive humidity,
wetness, dust, flammable gases, steam or solvents.
· If you have reason to believe that it is no longer
possible to work safely with the device, switch it off
and secure against unintentional start-up. You can
assume that it is no longer possible with the device
work when the tool:
- shows obvious signs of damage
- does not work properly or at all
- has been stored for a long time in unsuitable con-
ditions
Do not use the stylus on painted materials.
Make sure that the surface of the material is clean,
level and free of grease.
Always work in a well-ventilated area, as vapors may
cause irritation or damage to the eyes or respiratory
system.
· When creating decorations, apply even pressure to
the pen and move it at the same speed to create the
same dark lines.
· When working with sensitive material, such as thin
skin, be careful not to destroy the object you are
working on.
- Use protective equipment against noise, dust and
vibration !!!
SAVE THESE SAFETY INSTRUCTIONS !!!
DESCRIPTION (A)
This product is designed for creative work with va-
rious materials. Allows you to burn pictures and letters
into wood, leather or cork. The set includes various
firing tips and stamps. The product can also be used
for soldering of smaller dimensions and as a hot knife,
for example for cutting polystyrene.
1 Burning pen
2 10 x firing tip
3 9 x firing pattern
4 Soldering tip ·
5 Cutting Blade
6 Blade holder
7 Stand
8 Handle
9 Cable
Pictograms
Pictograms on the product packaging:
a) Power supply values
b) Power consumption
c) Max. temperature

USE AND OPERATION

ASIST tools are intended for home or hobby use only.
The manufacturer and importer do not recommend
using this tool in extreme conditions and under high
loads.
Any additional requirements must be the subject of
an agreement between the manufacturer and the
customer.
When working, use a flat, fireproof pad.
Be careful not to drop the product. There is a risk of
injury and fire.
Switching on the product
Make sure the product is not plugged in. If necessary,
wait until the stylus has cooled down completely - risk
of severe burns.
Select the desired tool and screw it clockwise onto
the stylus.
Use a suitable tool for this. Make sure that the han-
dpiece is seated securely and cannot come loose.
Do not use excessive force when screwing the han-
dpiece.
34