Wall Mounting - DeWalt SDS MAX DCH832 Guide D'utilisation

English
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature
is between 65 °F – 75 °F (18 ° C– 24 °C). DO NOT charge
when the battery pack is below +40 °F (+4.5 °C), or
above +104 °F (+40 °C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

Some D WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
8
Bail/Loop Style Auxiliary Handle (Fig. D)

WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the bail/loop style
auxiliary handle properly installed. Failure to do so may
result in the bail/loop style auxiliary handle slipping
during tool operation and subsequent loss of control.
Hold tool with both hands to maximize control.
The bail/loop style auxiliary handle
of the gear case and may be rotated 360˚ to permit right- or
left-hand use.
Mounting the Bail/Loop Style Auxiliary
Handle (Fig. D)
1. Widen the ring opening
auxiliary handle 2 by rotating the screw for handle
mounting 14 counter clockwise.
2. Slide the assembly onto the nose of the tool through
the ring opening
13
collar , past the chisel holder and sleeve.
3
3. Rotate the bail/loop style auxiliary handle to the
desired position.
4. Lock the bail/loop style auxiliary handle in place by
securely tightening the screw for handle mounting
rotating it clockwise so that the assembly will not rotate.
Bit and Bit Holder

WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and
bits may get extremely hot during operation. Small bits
of broken material may damage bare hands.
The rotary hammer can be fitted with various chisel bits
depending on the desired application. Use sharp drill
bits only.
Inserting and Removing SDS Max® Bits
(Fig. E)
1. Clean the insert shank end of the accessory to remove
any debris, then lightly grease with a light oil or lubricant.
2. Insert bit in the bit holder
pressure while rotating to secure the bit into place. The
bit shank must be clean.
3. Ensure the bit is properly engaged.
nOTE: The bit needs to move several centimeters in and
out of the bit holder 6
4. To remove the bit, pull back the locking sleeve
pull the bit out.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. F)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
clamps to the front
2
13 of the bail/loop style
and onto the chisel position index
6 and apply downward
when properly engaged.
14
7 and