F.F. Group SCMS-DB 305 PLUS Notice Originale page 10

10 | English
TECHNICAL DATA
Article Number
Model
Maximum cutting
capacity Mitre (L/R) 45⁰ /
Bevel 0⁰ (W x H)
Maximum cutting
capacity Mitre (L/R) 45⁰ /
Bevel (L) 45⁰ (W x H)
Maximum cutting
capacity Mitre (L/R) 45⁰ /
Bevel (R) 45⁰ (W x H)
Sound pressure level (LpA)
Sound power level (LwA)
Uncertainty (K)
Net weight
IDENTIFICATION (FIG. 1, 2)
1. Switch trigger
2. Lower blade guard
3. Base plate
4. Side handle
5. Extension wing
6. Stop plate
7. Guide fence
8. Working clamp
9. Slide lock
10. Motor
11. Carbon brush cap
12. Operation handle
13. Belt cover
14. Shaft lock
15. Bevel level
16. Miter scale
17. Turn lock lever
18. Turn table
19. Laser
20. Stopper arm
21. Blade
OPERATION
PREPARING THE UNIT
Unpacking and completing the assembly should
be done on a flat and stable surface, with enough
space for moving the machine and its packaging,
always making use of suitable equipment.
WARNING
Always unplug your machine from power source be-
fore any adjustment.
To assemble the machine:
Release cutting head
1. Push down slightly on the switch handle.
2. Pull out the stop latch (Fig. 3.1).
3. Allow the cutting head to rise to the up posi-
46 614
SCMS-DB 305
PLUS
mm 235 x 102
mm 235 x 48
mm 235 x 40
dB(A) 92
dB(A) 105
dB 3
kg 19,5
tion.
WARNING
To avoid injury and damage to the saw, transport or
store the miter saw with the cutting head locked in
the down position using the stop latch. Never use
the stop latch to hold the cutting head in a down po-
sition for cutting operations.
Side handle
Insert the miter handle (Fig. 4.1) into the opening
in the miter table (Fig 4.2).
Dust bag
1. Squeeze the metal collar wings (Fig. 5.2) on the
dust bag (Fig. 5.1).
2. Place the dust bag neck opening around the
exhaust port (Fig. 5.3) and release the metal
collar wings.
WARNING
Do not use the dust bag when machining metals. The
hot chips or sparks may ignite saw dust or the bag
itself. Clean and remove sawdust from under the saw
frequently.
Extension wings
1. Loosen the knob (Fig. 6.1) then slide the exten-
sion table to desired position and tighten the
knob.
2. The stop plate is designed for use during repet-
itive cutting. Only use one stop plate at a time.
Rotate the stop plate (Fig. 6.3) to vertical po-
sition, and retighten the locking bolt (Fig. 6.2).
Working clamp
1. Place the working clamp assembly (Fig. 7.1) in
one of the mounting holes (Fig. 7.2).
2. The height of the clamp assembly can be ad-
justed by loosening knob (Fig. 7.3) located in
the back of clamp.
Base plate to bench
Place the saw in the desired location directly on a
workbench where there is room for handling and
proper support of the work piece. The base of the
saw has four mounting holes. Bolt the base of the
miter saw (Fig. 8.1) to the workbench (Fig. 8.5)
using bolt (Fig. 8.2), rubber washer (Fig. 8.3), flat
washers (Fig. 8.4, 8.6), lock washer (Fig. 8.7), nut
(Fig. 8.8) and lock nut (Fig. 8.9) as shown.
NOTE
Mounting hardware is not included with this tool.
Bolts, nuts, washers and screws must be purchased
separately.
Lock button
To prevent the switch trigger (Fig. 9.1) from be-
ing accidentally pulled, a lower blade guard lock
button (Fig. 9.2) is provided. To start the tool, pull
the lock button against blade guard and press the
switch trigger. Release the switch trigger and lock
button to stop.
WARNING
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to
the "OFF" position when released. Do not press the
SCMS-DB 305 PLUS