Cleaning And Storage; Technical Data - Clatronic BS 1254 Mode D'emploi & Garantie

Floor nozzle
To clean carpets or smooth surfaces.
Smooth fl oors:
Carpets:
Releasing the nozzles:
Vacuum power regulator (3)
Low vacuum power:
Medium vacuum power:
High vacuum power:
Telescopic Suction Tube (13)
As the length of the suction tube can be adjusted it can
be adapted to your own personal height. Unlock the
coupling by pressing the button (14) downwards.
Then move the telescopic suction tube to the desired
height. To fi x the suction tube in position, pull it until it is
heard to lock in place.
Cable winding device
Pull out the cable (1) up to the maximum length indicated
with the yellow mark. Never pull the cable out up to the
red mark as the cable winding can be damaged. Said
damages are not covered by the warranty.
Winding
Press the cable (5) winding button and guide the cable.
Hold the cable to avoid wrapping.
Air Slide
Open the air slide on the hose handle in order to regulate
the airfl ow or to clear any particles sticking to the nozzle.
Dust bag replacement display (8)
Hold the hose up into air. If the dust bag change display
lights up, the bag is full. Please change it.
Changing the dust bag
• Pull the plug out of the socket.
• Press the button (10) to open the lid of the dust bag
compartment (until its locks in place).
• Pull the dust bag out of the holder.
• Insert a new dust bag.
• Close the cover so that it snaps into place.
26
05-BS 1254 26
Press down the lever with the
brush symbol with your foot.
The brush is now visible.
Press the lever In the opposi-
te direction. The brushes are
now retracted.
Pull these off while turning
slightly.
For curtains and delicate
fabrics
For long-pile velour carpets
and textile fl ooring
For sturdy rugs and fl oors
Filter
Your appliance has two fi lters.
Motor protection fi lter (inlet fi lter)
The inlet fi lter is located in the dust bag compartment.
Press the button (10) to open the lid of the dust bag
compartment. The fi lter is located vertically in the rear
section of the dust housing. Remove the fi lter by pulling
upwards. Clean the engine protection fi lter after 10 dust
bag changes. If necessary, the fi lter can also be washed
in warm water without any additives. Place it back into
place only once it is completely dry!
Outlet fi lter
The appliance is also equipped with an outlet fi lter. This
fi lter is located in the dust bag space under the ventilation
grille. Open the dust bag compartment. Remove the fi lter
and clean as described above. Please reinsert the fi lter
correctly and then close the ventilation grille.
Coarse Dirt Filter
This collects the coarse dirt.
• Empty the container (7.2) when the MAX. mark is
reached.
• When suction power decreases!
Even if the MAX mark on the coarse dirt fi lter has not
yet been reached it is possible that the suction power
of your vacuum cleaner will decrease. You should
then also clean the container.
• In order to do so, remove the container and the cover.
• Note: The components can be removed or attached
by means of short twists in a clockwise or anticlo-
ckwise direction. Under the cover 7.1 there is an air
duct that also has to be cleaned.

Cleaning and storage

Cleaning
• Pull the plug out of the socket before cleaning!
• Clean the casing with a dry cloth.
Storage
• Let the iron cool down completely.
• Wind the cable completely.
• Please place the machine in a vertical position and
insert the hook on the suction tube into the parking
assistance on the back.

Technical Data

Model: ................................................................. BS 1254
Power supply: ................................................230 V, 50 Hz
Power consumption:
P :................................................................. 1800 W
nom.
P :................................................................. 2300 W
max.
Protection class: ..............................................................ΙΙ
This device has been tested according to all relevant cur-
rent CE guidelines, such as electromagnetic compatibility
and low voltage directives, and has been constructed in
accordance with the latest safety regulations.
20.02.2006, 14:26:42 Uhr