Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

G
MATERIALS
A
1
Cross Bar
B
4
Bushes (14mm O.D. x 54mm Long)
C
2
M10 x 35 x 1.5mm Bolts, Lock Washers and Flat Washers (25mm O.D.)
D
4
M10 x 90 Bolts, Nuts, Lock Washers, Flat Washers (30mm O.D.) and Large Flat Washers (40mm O.D.)
E
1
Left Hand Side Arm
F
1
Right Hand Side Arm
G
4
M10 x 35 x 1.5mm Bolts, Lock Washers and Flat Washers (25mm O.D.)
H
4
Nut Retainers and M10 x 1.5mm Square Nuts.
I
1
Z99 Flip up Electrical plate.
For use with
C48Q Detachable neck option – ZQ2030. Please refer to ZQ fitting instructions for installation
FITTING
1. Remove spare wheel. Lower rear exhaust hanger. Insert Bushes (B) into frame from outside faces.
2. Insert captive fasteners (H) into side arms as per Fastener diagrams.
3. Loosely attach Side Arms (E) and (F) using Bolts (D).
4. Insert captive fasteners (H) onto top of crossbar (A) and fit to rear panel mountings using Bolts (C). Note: It is
advisory to open up rear panel mounts for Bolts (C). Attach Cross Bar (A) to Side Arms (E) and (F) using Bolts
(G).
5. Attach preferred Neck option and rise to its highest position, fit Z99 electrical plate and tighten all bolts. Re-
mount exhaust hanger and spare wheel.
Recommended torque settings: Grade 8.8 bolts: M10 - 52 Nm, M12 - 80 Nm.
Fitting
Instructions
=AzaleaCode128A(A2)
W0001C48-FIT$010911170000
TOWBAR
For CITROEN XSARA PICASSO
2000-2009
C48U for
C48Q

Publicité

loading

Sommaire des Matières pour Witter C48U

  • Page 1 Fitting TOWBAR C48U for For CITROEN XSARA PICASSO C48Q 2000-2009 Instructions MATERIALS Cross Bar Bushes (14mm O.D. x 54mm Long) M10 x 35 x 1.5mm Bolts, Lock Washers and Flat Washers (25mm O.D.) M10 x 90 Bolts, Nuts, Lock Washers, Flat Washers (30mm O.D.) and Large Flat Washers (40mm O.D.)
  • Page 3 Notice de Attelage Pour CITROEN XSARA PICASSO C48U Montage 2000-2009 Désignation Traverse principale conforme à la norme Européenne 94/20/EC A50-1 Entretoises (Ø14mm O.D. x 54mm Longue) Boulons M10 x 35 x 1.5mm, rondelles frein et rondelles plates (Ø 25mm.) Boulons M10 x 90, écrous, rondelles frein, rondelles plates (Ø 30mm.) et grande rondelles plates (Ø...
  • Page 4 Guide d’installation pour les écrous prisonnier ATTENTION : Ces écrous prisonniers spéciaux sont conçus pour céder si le couple de serrage est dépassé, pour protéger le filetage de l’écrou de tout dommage NE PAS DEPASSER LE COUPLE DE SERRAGE-M12 : 80Nm, M10 : 52Nm Insertion d’un écrou prisonnier dans son logement (ex.

Ce manuel est également adapté pour:

C48q