Battery Care - Worx WG775 Manuel D'utilisation

BATTERY CARE

The battery in your cordless lawnmower is a
24-volt sealed lead acid system. The battery
can be stored in any position without fear of
leakage.
• For optimal battery life and performance
the battery should be fully charged every 2
months during storage
• For optimal battery life and performance,
the battery should be fully charged after
each use
• Store the battery in a cool dry location.
• The battery can be safely stored down to
14°F (-10°C).
• The battery does not need to be fully
discharged before recharging.
• Initially 2 to 3 charging cycles may be
required after purchase to achieve the
maximum run time capacity.
The battery is maintenance-free and requires
no service. ADDITIONAL BATTERIES can be
purchased from the WORX Customer Helpline
1-866-354-9679.
14
ASSEmBlY
imPOrTaNT! Before you assemble
the lawn mower, check the accessories
according to the above information, make sure
the accessories are included and functional.
1.fiTTiNg THE HaNdlE bar (see fig.
b1-b4)
1) Remove the screws (a) on both sides of the
deck (See Fig. B1) .
2) Insert the Lower Handle Bar (8) into the
holes on the deck. Be sure to carefully
align the screw holes found on the Lower
Handles with the screws holes found on the
deck (a) (See Fig. B1, B2).
3) Secure the Lower Handle Bars to the deck
with the screws provided (See Fig. B2).
4) Attach the Upper Handle (1) with the bolts
and Lock Cam Lever (7) to the Lower
Handle (8) (See Fig. B4).
5) Tightening Locking Cam Lever (7). Check
that the handle is FULLY secured.
The cam lever pressure can be adjusted by
rotating the Locking Cam Lever clockwise/
3-in-1 Cordless lawn mower
counterclockwise (See Fig. B4). DO NOT
OVER TIGHTEN.
NOTE: Ensure that the bolts are fully
inserted through the handles before
adjusting or tightening the Locking Cam
Lever (7).
6) Attach the cable clips (3) provided, to the
upper and lower handle. Insert the cable
into the clips ensuring there is enough
cable slack (See Fig. B3).
2. grass COllECTiON bag assEmbly
1) Attach the Grass Collection Bag handle
to the grass bag assembly as shown in
Fig C1-C4.
a. Identify the front and rear of both the
handle and the Grass Collection Bag(5)
assembly (See Fig. C1).
b. Insert the front portion of the handle
into position (See Fig. C2).
c. Secure the front portion of the handle
in place by pushing it forward (See Fig.
C2).
d. Insert and secure the rear portion of
the handle in position by pushing down
on the back of the handle. Ensure that
"clicks" into position (See Fig. C2) .
2) Clip the plastic clips of the Grass
Collection Bag over the metal frame
(See Fig. C3) .
warNiNg: make sure to not fit the
handle in the reverse direction as it
will not remain secure. make sure to fit
the handle as shown in fig. C4.
3. aTTaCHiNg THE grass COllECTiON
bag TO THE mOwEr (see fig. d1, d2, d3)
NOTE: The grass bag is held in place by
the safety flap.
1. Switch the mower off, remove the Safety
Key (6) and wait until the mower Blade (16)
has stopped.
2. Raise the Safety Flap (9) and hold it in the
upward position while the Grass Collection
Bag (5) is properly located below it (See
Fig. D1).
3. Position the lower edge of the Grass
Collection Bag on the plastic tabs (b) found
below the rear discharge chute on the
mower deck. (See Fig. D2) .
EN