Conrad UTP Mode D'emploi page 2

G
O P E R A T I N G I N S T R U C T I O N S
Network extension
via UTP
Item no. 800916
Intended use
The product is used to set up a network connection via UTP cable (Cat5E, Cat6 or two wire-
system). Therefore, it is possible to continue using a simple, existing UTP cable in order to
operate a network or corresponding network devices without laying a new cable.
The transceiver supports PoE. The corresponding power supply unit is not enclosed but needs
to be purchased separately.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product and involves
the risk of short circuits, fire, electric shock, etc. No part of the product may be modified or
converted.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Contents
• 1x transceiver
• 1x RJ45-Y distributor
• Quick guide
• Manufacturer's operating instructions in English
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! The
warranty will be void in such cases!
• Unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons (CE).
• The product is not a toy and should be kept out of the reach of children!
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
Connection
The manufacturer's operating instructions include an illustration for a possible connection be-
tween the transceivers, two terminals and the network.
One of the transceivers should be connected to the existing network using a network cable
(e.g. via switch or router).
Be sure to not to use the TWP-connector but the connector next to the low-voltage
female connector!
You also have to connect an appropriate power supply unit to the transceiver (not enclosed,
to be ordered separately) which provides the power end electricity supply for PoE (48 V/DC,
output power depending on the connected devices).
The other transceivers should be connected to the terminals using the RJ45-connector, e.g.
a network camera, an access point and so on. In case you are using terminals that are PoE-
ready, the transceiver will later provide the required energy for the operation.
Be sure to not to use the TWP-connector but the connector next to the low-voltage
female connector!
Then, establish the cable connection between the transceivers (using the TWP-connectors),
enclosed you will find a RJ45-Y distributor for the operation of two terminals. In that case, you
will need more network cables for the connection of the transceiver to the RJ45-Y distributor.
That way, it is possible to operate a total of four terminals (each terminal requires
one transceiver).
When setting up the device, the transceivers will find themselves, therefore no configuration
www.conrad.com
is required.
For special operation purposes, the transceivers can be leaned against each other ("Joining")
or separated ("Un-Joined"). Respective information can be found in the manufacturer's operat-
Version 02/15
ing instructions in English.
Example for 2 terminals (connection position on the RJ45-Y distributor is irrelevant):
A
B
Example for one terminal:
A
A = terminal 1
B = terminal 2
C = connection to switch/router
D = External power adapter (48 V/DC, output dependent upon the connected devices)
The power-LED is lit when power/electricity is provided by the power supply unit. The TWP-
LED is lit, if a data connection via UTP-cable has been established, the PoE-LED is lit with an
existing PoE-connection.
Corresponding ports are provided on the housing for the installation. You can, however, also
use a double-sided adhesive tape or a cable fixer.
Disposal
Technical data
Network ................................ 10/100Base T, half-/full-duplex, IEEE802.3 af/at
Conector ............................... RJ45
Frequency band .................... 1.8 to 30 MHz
UTP cable length .................. Up to 500 m max. (depending on the quality of the used UTP
Operating voltage ................. 48 V/DC (via an external power supply unit)
Power consumption .............. approx. 2.5 W
Operating temperature ......... -10 °C to +50 °C
Operational air humidity ........ 0% to 90% relative air humidity, non-condensing
Dimensions ........................... 42 x 40 x 102.5 mm (W x H x D)
One "terminal" is, for example, an IP-surveillance camera, one access point, another
switch or a VoIP-telephone and so on.
Electrical and electronic devices should not be disposed of in the household
waste.
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
cable/plug and so on)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical status at the time of
printing.
© Copyright 2015 by Conrad Electronic SE.
C
D
C
D