Mounting And Operation - HIKOKI BL36200 (SA) Mode D'emploi

English
Before
charging
While
charging
Charging
Charge
complete
indicator lamp
(RED / BLUE
/ GREEN /
PURPLE)
Overheat
standby
Charging
impossible
● Regarding the temperature and charging time of the
back pack power supply
The temperatures and charging time will become as
shown in Table 3.
Battery
Charging voltage
Type of battery
Temperatures at which the back pack
power supply can be recharged
Charging time for battery capacity,
approx.(At 20oC)
21 Ah
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the adapter of
back pack power supply.
NOTE
Be sure to pull out the adapter of back pack power
supply from the charger after use, and then keep it.
When the back pack power supply is not in use, switch
it OFF.
CAUTION
○ If the back pack power supply are charged while it is
heated because it has been left for a long time in a
location subject to direct sunlight or because the back
pack power supply have just been used, the charge
indiactor lamp of the charger lights for 0.3 seconds,
does not light for 0.3 seconds (off for 0.3 seconds). In
such a case, fi rst let the back pack power supply cool,
then start charging.
○ When the charge indiactor lamp fl ickers in purple (at
0.2-seconds intervals), check for and take out any
foreign objects in the charger's battery connector. If
there are no foreign objects, it is probable that the back
pack power supply or charger is malfunctioning. Take it
to your authorized Service Center.
Indications of the charge indicator lamp
Lights for 0.5 seconds. Does not light for
Blinks
0.5 seconds. (off for 0.5 seconds)
(RED)
Lights continuously
Lights
(BLUE)
Lights continuously
Lights
(GREEN)
(Continuous buzzer sound: about 6
seconds)
Lights for 0.3 seconds. Does not light for
Blinks
0.3 seconds. (off for 0.3 seconds)
(RED)
Lights for 0.1 seconds. Does not light for
0.1 seconds. (off for 0.1 seconds)
Flickers
(PURPLE)
(Intermittent buzzer sound: about 2
seconds)
Table 3
Charger
UC36YSL
V 36 V
Li-ion
0oC – 50oC
h.
Table 2
○ Since the built-in microcomputer takes about 3 seconds
to confi rm that the back pack power supply being
charged with UC36YSL is taken out, wait for a minimum
of 3 seconds before reinserting it to continue charging.
If the adapter of back pack power supply is reinserted
within 3 seconds, the back pack power supply may not
be properly charged.

MOUNTING AND OPERATION

Pull-out direction of the output
cord from the high-capacity
power supply
3 Attaching the carrier
Attaching the carrier strap
Storing the switch panel
BL36200 (SA)
Relation between adapter and
cordless power tools
BL36200 (S)
Relation between adapter and
cordless power tools
Connecting power supply
connectors and adapter
connectors
Examples showing how to use
the arm band
Main switch
Power switch
Charging the high-capacity
power supply
Using the power supply to power
cordless power tools
Warning lamp indications
Remaining capacity indications
Using the power supply to power
USB devices
6
Plugged into power source
Back pack power supply
overheated.
Unable to charge. (Charging
will commence when back
pack power supply cools)
Malfunction in the back pack
power supply or the charger
Action Figure Page
1 157
2 157
3 157
4 157
5 157
6 157
7 158
8 158
9 158
10 158
11 158
12 158
13 159
14 159
15 159