Completing The Set Up - Samsung RF24FSEDBSR Mode D'emploi

3. Connect the water line installation kit to the
shut off valve.
Cold water line Cold water line
Pipe clamp Pipe clamp
Shut off valve Shut off valve
Connecting the water supply line to
the refrigerator.
There are several items that you need to purchase
to complete this connection.
You may fi nd these items sold as a kit at your local
hardware store.
Use Copper Tubing
• ¼" copper tubing
• ¼" compression nut
(1pc)
• Ferrule (2pc)
Compression Compression
Nut (1/4") Nut (1/4")
(Assembled) (Assembled)
Ferrule Ferrule
(Not supplied) (Not supplied)
Copper tubing Copper tubing
(Not supplied) (Not supplied)
Household water supply line Household water supply line
1. Connect the household water line to the
assembled compression fi tting.
- If you are using copper tubing, slip the
compression nut ( B ) (not supplied) and
ferrule (not supplied) on the copper tubing (not
supplied) as shown.
- If you are using plastic tubing ( B ) , insert the
molded end (Bulb) of the plastic tubing ( B )
into the compression fi tting.
Do not use without the molded end (Bulb)
of the plastic tubing ( B ).
CAUTION
DA68-02897A(0.1).indb 15 DA68-02897A(0.1).indb 15
Water line installation kit Water line installation kit
Use Plastic Tubing
• ¼" plastic tubing
→ Molded end(Bulb)
• ¼" compression nut
(1pc)
Refrigerator
Plastic Tubing Plastic Tubing
(Assembled) (Assembled)
Compression Compression
Fitting Fitting
(Assembled) (Assembled)
Molded Molded
end(Bulb) end(Bulb)
Compression Compression
nut (B) (1/4") nut (B) (1/4")
(Not supplied) (Not supplied)
Plastic tubing (B) Plastic tubing (B)
or or
(Not supplied) (Not supplied)
2. Tighten the compression nut ( B ) onto the
compression fi tting.
Do not over-tighten the compression nut ( B ) .
3. Turn the water on and check for any leakage.
If you fi nd water drops or leakage in the
connection areas, turn off the main water
supply. Check the connections and, if
necessary, tighten.
4. Flush 1 gallon of water through the fi lter
before drinking or using the water from the
refrigerator. (Flush approximately 6 minutes.)
To fl ush, press a large glass or cup against the
water dispenser lever. Fill the glass, empty it
into the kitchen sink after it is fi lled, and then
repeat.
5. After you turn on the refrigerator, let the ice
maker make ice for 1 to 2 days. Over that
period of time, throw out the fi rst 1 or 2
buckets of ice the freezer makes to ensure all
impurities have been removed from the water
line.
Only connect the water line to a drinkable
water source.
If you have to repair or disassemble the water line,
cut off 1/4" of the plastic tubing to make sure you
get a snug, leak-free connection.
You can test the water line quickly using a
paper cup. Under normal conditions, the
water dispenser can fi ll a 5.75 oz. (170cc)
cup in about 10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
1. Make sure your refrigerator is in an appropriate
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
2. Once the refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
3. Set the Temperature control to the coldest
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
4. After you plug the refrigerator in, it will
take a few hours to reach the appropriate
temperature. You can store food and drinks
in the refrigerator after the temperature is
suffi ciently cool.
setting up _15
13. 03. 13 오전 8:38 13. 03. 13 오전 8:38